diff --git a/BTD.cpp b/BTD.cpp index a1561e7c..216ffcc4 100755 --- a/BTD.cpp +++ b/BTD.cpp @@ -16,7 +16,7 @@ */ #include "BTD.h" -// To enable serial debugging uncomment "#define DEBUG_USB_HOST" in message.h +// To enable serial debugging see "settings.h" //#define EXTRADEBUG // Uncomment to get even more debugging data const uint8_t BTD::BTD_CONTROL_PIPE = 0; @@ -403,14 +403,10 @@ void BTD::HCI_event_task() { break; case EV_COMMAND_STATUS: - if (hcibuf[2]) { // show status on serial if not OK + if (hcibuf[2]) { // Show status on serial if not OK #ifdef DEBUG_USB_HOST Notify(PSTR("\r\nHCI Command Failed: "), 0x80); D_PrintHex (hcibuf[2], 0x80); - Notify(PSTR(" "), 0x80); - D_PrintHex (hcibuf[4], 0x80); - Notify(PSTR(" "), 0x80); - D_PrintHex (hcibuf[5], 0x80); #endif } break; @@ -466,15 +462,18 @@ void BTD::HCI_event_task() { case EV_CONNECT_COMPLETE: hci_event_flag |= HCI_FLAG_CONNECT_EVENT; if (!hcibuf[2]) { // check if connected OK +#ifdef EXTRADEBUG + Notify(PSTR("\r\nConnection established"), 0x80); +#endif hci_handle = hcibuf[3] | ((hcibuf[4] & 0x0F) << 8); // store the handle for the ACL connection hci_event_flag |= HCI_FLAG_CONN_COMPLETE; // set connection complete flag - } -#ifdef DEBUG_USB_HOST - else { - Notify(PSTR("\r\nConnection Failed"), 0x80); + } else { hci_state = HCI_CHECK_WII_SERVICE; - } +#ifdef DEBUG_USB_HOST + Notify(PSTR("\r\nConnection Failed: "), 0x80); + D_PrintHex (hcibuf[2], 0x80); #endif + } break; case EV_DISCONNECT_COMPLETE: @@ -971,16 +970,20 @@ void BTD::hci_inquiry_cancel() { } void BTD::hci_connect() { + hci_connect(disc_bdaddr); // Use last discovered device +} + +void BTD::hci_connect(uint8_t *bdaddr) { hci_event_flag &= ~(HCI_FLAG_CONN_COMPLETE | HCI_FLAG_CONNECT_EVENT); hcibuf[0] = 0x05; hcibuf[1] = 0x01 << 2; // HCI OGF = 1 hcibuf[2] = 0x0D; // parameter Total Length = 13 - hcibuf[3] = disc_bdaddr[0]; // 6 octet bdaddr - hcibuf[4] = disc_bdaddr[1]; - hcibuf[5] = disc_bdaddr[2]; - hcibuf[6] = disc_bdaddr[3]; - hcibuf[7] = disc_bdaddr[4]; - hcibuf[8] = disc_bdaddr[5]; + hcibuf[3] = bdaddr[0]; // 6 octet bdaddr (LSB) + hcibuf[4] = bdaddr[1]; + hcibuf[5] = bdaddr[2]; + hcibuf[6] = bdaddr[3]; + hcibuf[7] = bdaddr[4]; + hcibuf[8] = bdaddr[5]; hcibuf[9] = 0x18; // DM1 or DH1 may be used hcibuf[10] = 0xCC; // DM3, DH3, DM5, DH5 may be used hcibuf[11] = 0x01; // Page repetition mode R1 @@ -1079,7 +1082,7 @@ void BTD::hci_disconnect(uint16_t handle) { // This is called by the different s } void BTD::hci_write_class_of_device() { // See http://bluetooth-pentest.narod.ru/software/bluetooth_class_of_device-service_generator.html - hcibuf[0] = 0x24; // HCI OCF = 3 + hcibuf[0] = 0x24; // HCI OCF = 24 hcibuf[1] = 0x03 << 2; // HCI OGF = 3 hcibuf[2] = 0x03; // parameter length = 3 hcibuf[3] = 0x04; // Robot @@ -1259,9 +1262,9 @@ void BTD::setBdaddr(uint8_t* bdaddr) { buf[1] = 0x00; for (uint8_t i = 0; i < 6; i++) - buf[i + 2] = bdaddr[5 - i]; // Copy into buffer, has to be written reversed + buf[i + 2] = bdaddr[5 - i]; // Copy into buffer, has to be written reversed, so it is MSB first - // bmRequest = Host to device (0x00) | Class (0x20) | Interface (0x01) = 0x21, bRequest = Set Report (0x09), Report ID (0xF5), Report Type (Feature 0x03), interface (0x00), datalength, datalength, data) + // bmRequest = Host to device (0x00) | Class (0x20) | Interface (0x01) = 0x21, bRequest = Set Report (0x09), Report ID (0xF5), Report Type (Feature 0x03), interface (0x00), datalength, datalength, data pUsb->ctrlReq(bAddress, epInfo[BTD_CONTROL_PIPE].epAddr, bmREQ_HID_OUT, HID_REQUEST_SET_REPORT, 0xF5, 0x03, 0x00, 8, 8, buf, NULL); } @@ -1277,6 +1280,6 @@ void BTD::setMoveBdaddr(uint8_t* bdaddr) { for (uint8_t i = 0; i < 6; i++) buf[i + 1] = bdaddr[i]; - // bmRequest = Host to device (0x00) | Class (0x20) | Interface (0x01) = 0x21, bRequest = Set Report (0x09), Report ID (0x05), Report Type (Feature 0x03), interface (0x00), datalength, datalength, data) + // bmRequest = Host to device (0x00) | Class (0x20) | Interface (0x01) = 0x21, bRequest = Set Report (0x09), Report ID (0x05), Report Type (Feature 0x03), interface (0x00), datalength, datalength, data pUsb->ctrlReq(bAddress, epInfo[BTD_CONTROL_PIPE].epAddr, bmREQ_HID_OUT, HID_REQUEST_SET_REPORT, 0x05, 0x03, 0x00, 11, 11, buf, NULL); } diff --git a/BTD.h b/BTD.h index c6a705a9..27b3794e 100755 --- a/BTD.h +++ b/BTD.h @@ -219,7 +219,13 @@ public: * @return Returns true if the device's VID and PID matches this driver. */ virtual boolean VIDPIDOK(uint16_t vid, uint16_t pid) { - return ((vid == PS3_VID || vid == IOGEAR_GBU521_VID) && (pid == PS3_PID || pid == PS3NAVIGATION_PID || pid == PS3MOVE_PID || pid == IOGEAR_GBU521_PID)); + if (vid == IOGEAR_GBU521_VID && pid == IOGEAR_GBU521_PID) + return true; + if (my_bdaddr[0] != 0x00 || my_bdaddr[1] != 0x00 || my_bdaddr[2] != 0x00 || my_bdaddr[3] != 0x00 || my_bdaddr[4] != 0x00 || my_bdaddr[5] != 0x00) { // Check if Bluetooth address is set + if (vid == PS3_VID && (pid == PS3_PID || pid == PS3NAVIGATION_PID || pid == PS3MOVE_PID)) + return true; + } + return false; }; /**@}*/ @@ -307,8 +313,13 @@ public: void hci_inquiry(); /** Cancel a HCI inquiry. */ void hci_inquiry_cancel(); - /** Connect to a device. */ + /** Connect to last device communicated with. */ void hci_connect(); + /** + * Connect to device. + * @param bdaddr Bluetooth address of the device. + */ + void hci_connect(uint8_t *bdaddr); /** Used to a set the class of the device. */ void hci_write_class_of_device(); /**@}*/ diff --git a/PS3BT.cpp b/PS3BT.cpp index 6f9a4d23..9ed5da75 100644 --- a/PS3BT.cpp +++ b/PS3BT.cpp @@ -16,7 +16,7 @@ */ #include "PS3BT.h" -// To enable serial debugging uncomment "#define DEBUG_USB_HOST" in message.h +// To enable serial debugging see "settings.h" //#define EXTRADEBUG // Uncomment to get even more debugging data //#define PRINTREPORT // Uncomment to print the report send by the PS3 Controllers @@ -36,14 +36,14 @@ pBtd(p) // pointer to USB class instance - mandatory HIDBuffer[0] = 0x52; // HID BT Set_report (0x50) | Report Type (Output 0x02) HIDBuffer[1] = 0x01; // Report ID - //Needed for PS3 Move Controller commands to work via bluetooth + // Needed for PS3 Move Controller commands to work via bluetooth HIDMoveBuffer[0] = 0xA2; // HID BT DATA_request (0xA0) | Report Type (Output 0x02) HIDMoveBuffer[1] = 0x02; // Report ID /* Set device cid for the control and intterrupt channelse - LSB */ - control_dcid[0] = 0x40; //0x0040 + control_dcid[0] = 0x40; // 0x0040 control_dcid[1] = 0x00; - interrupt_dcid[0] = 0x41; //0x0041 + interrupt_dcid[0] = 0x41; // 0x0041 interrupt_dcid[1] = 0x00; Reset(); @@ -56,25 +56,19 @@ bool PS3BT::getButtonPress(Button b) { bool PS3BT::getButtonClick(Button b) { uint32_t button = pgm_read_dword(&BUTTONS[(uint8_t)b]); bool click = (ButtonClickState & button); - ButtonClickState &= ~button; // clear "click" event + ButtonClickState &= ~button; // Clear "click" event return click; } uint8_t PS3BT::getAnalogButton(Button a) { - if (l2capinbuf == NULL) - return 0; return (uint8_t)(l2capinbuf[pgm_read_byte(&ANALOGBUTTONS[(uint8_t)a])]); } uint8_t PS3BT::getAnalogHat(AnalogHat a) { - if (l2capinbuf == NULL) - return 0; return (uint8_t)(l2capinbuf[(uint8_t)a + 15]); } int16_t PS3BT::getSensor(Sensor a) { - if (l2capinbuf == NULL) - return 0; if (PS3Connected) { if (a == aX || a == aY || a == aZ || a == gZ) return ((l2capinbuf[(uint16_t)a] << 8) | l2capinbuf[(uint16_t)a + 1]); @@ -92,13 +86,11 @@ int16_t PS3BT::getSensor(Sensor a) { } double PS3BT::getAngle(Angle a) { - double accXval; - double accYval; - double accZval; + double accXval, accYval, accZval; if (PS3Connected) { // Data for the Kionix KXPC4 used in the DualShock 3 - const double zeroG = 511.5; // 1.65/3.3*1023 (1,65V) + const double zeroG = 511.5; // 1.65/3.3*1023 (1.65V) accXval = -((double)getSensor(aX) - zeroG); accYval = -((double)getSensor(aY) - zeroG); accZval = -((double)getSensor(aZ) - zeroG); @@ -114,13 +106,10 @@ double PS3BT::getAngle(Angle a) { // Convert to 360 degrees resolution // atan2 outputs the value of -π to π (radians) // We are then converting it to 0 to 2π and then to degrees - if (a == Pitch) { - double angle = (atan2(accYval, accZval) + PI) * RAD_TO_DEG; - return angle; - } else { - double angle = (atan2(accXval, accZval) + PI) * RAD_TO_DEG; - return angle; - } + if (a == Pitch) + return (atan2(accYval, accZval) + PI) * RAD_TO_DEG; + else + return (atan2(accXval, accZval) + PI) * RAD_TO_DEG; } double PS3BT::get9DOFValues(Sensor a) { // Thanks to Manfred Piendl @@ -168,11 +157,7 @@ String PS3BT::getTemperature() { } bool PS3BT::getStatus(Status c) { - if (l2capinbuf == NULL) - return false; - if (l2capinbuf[(uint16_t)c >> 8] == ((uint8_t)c & 0xff)) - return true; - return false; + return (l2capinbuf[(uint16_t)c >> 8] == ((uint8_t)c & 0xff)); } String PS3BT::getStatusString() { @@ -266,8 +251,7 @@ void PS3BT::ACLData(uint8_t* ACLData) { } } if (((ACLData[0] | (ACLData[1] << 8)) == (hci_handle | 0x2000))) { //acl_handle_ok - for (uint8_t i = 0; i < BULK_MAXPKTSIZE; i++) - l2capinbuf[i] = ACLData[i]; + memcpy(l2capinbuf, ACLData, BULK_MAXPKTSIZE); if ((l2capinbuf[6] | (l2capinbuf[7] << 8)) == 0x0001) { //l2cap_control - Channel ID for ACL-U if (l2capinbuf[8] == L2CAP_CMD_COMMAND_REJECT) { #ifdef DEBUG_USB_HOST @@ -457,8 +441,7 @@ void PS3BT::L2CAP_task() { Notify(PSTR("\r\nHID Interrupt Successfully Configured"), 0x80); #endif if (remote_name[0] == 'M') { // First letter in Motion Controller ('M') - for (uint8_t i = 0; i < BULK_MAXPKTSIZE; i++) // Reset l2cap in buffer as it sometimes read it as a button has been pressed - l2capinbuf[i] = 0; + memset(l2capinbuf, 0, BULK_MAXPKTSIZE); // Reset l2cap in buffer as it sometimes read it as a button has been pressed l2cap_state = L2CAP_HID_PS3_LED; } else l2cap_state = L2CAP_HID_ENABLE_SIXAXIS; @@ -497,8 +480,7 @@ void PS3BT::Run() { switch (l2cap_state) { case L2CAP_HID_ENABLE_SIXAXIS: if (millis() - timer > 1000) { // loop 1 second before sending the command - for (uint8_t i = 0; i < BULK_MAXPKTSIZE; i++) // Reset l2cap in buffer as it sometimes read it as a button has been pressed - l2capinbuf[i] = 0; + memset(l2capinbuf, 0, BULK_MAXPKTSIZE); // Reset l2cap in buffer as it sometimes read it as a button has been pressed for (uint8_t i = 15; i < 19; i++) l2capinbuf[i] = 0x7F; // Set the analog joystick values to center position enable_sixaxis(); @@ -529,16 +511,16 @@ void PS3BT::Run() { ButtonState = 0; // Clear all values OldButtonState = 0; ButtonClickState = 0; - + onInit(); // Turn on the LED on the controller l2cap_state = L2CAP_DONE; } break; case L2CAP_DONE: - if (PS3MoveConnected) { //The Bulb and rumble values, has to be send at aproximatly every 5th second for it to stay on - if (millis() - timerBulbRumble > 4000) { //Send at least every 4th second - HIDMove_Command(HIDMoveBuffer, HID_BUFFERSIZE); //The Bulb and rumble values, has to be written again and again, for it to stay turned on + if (PS3MoveConnected) { // The Bulb and rumble values, has to be send at aproximatly every 5th second for it to stay on + if (millis() - timerBulbRumble > 4000) { // Send at least every 4th second + HIDMove_Command(HIDMoveBuffer, HID_BUFFERSIZE); // The Bulb and rumble values, has to be written again and again, for it to stay turned on timerBulbRumble = millis(); } } @@ -550,18 +532,22 @@ void PS3BT::Run() { /* HID Commands */ /************************************************************/ -//Playstation Sixaxis Dualshock and Navigation Controller commands +// Playstation Sixaxis Dualshock and Navigation Controller commands void PS3BT::HID_Command(uint8_t* data, uint8_t nbytes) { - if (millis() - timerHID <= 250)// Check if is has been more than 250ms since last command - delay((uint32_t)(250 - (millis() - timerHID))); //There have to be a delay between commands + if (millis() - timerHID <= 150) // Check if is has been more than 150ms since last command + delay((uint32_t)(150 - (millis() - timerHID))); // There have to be a delay between commands pBtd->L2CAP_Command(hci_handle, data, nbytes, control_scid[0], control_scid[1]); // Both the Navigation and Dualshock controller sends data via the control channel timerHID = millis(); } void PS3BT::setAllOff() { - for (uint8_t i = 0; i < PS3_REPORT_BUFFER_SIZE; i++) - HIDBuffer[i + 2] = pgm_read_byte(&PS3_REPORT_BUFFER[i]); // First two bytes reserved for report type and ID + HIDBuffer[3] = 0x00; // Rumble bytes + HIDBuffer[4] = 0x00; + HIDBuffer[5] = 0x00; + HIDBuffer[6] = 0x00; + + HIDBuffer[11] = 0x00; // LED byte HID_Command(HIDBuffer, HID_BUFFERSIZE); } @@ -596,6 +582,7 @@ void PS3BT::setLedRaw(uint8_t value) { HIDBuffer[11] = value << 1; HID_Command(HIDBuffer, HID_BUFFERSIZE); } + void PS3BT::setLedOff(LED a) { HIDBuffer[11] &= ~((uint8_t)((pgm_read_byte(&LEDS[(uint8_t)a]) & 0x0f) << 1)); HID_Command(HIDBuffer, HID_BUFFERSIZE); @@ -611,7 +598,7 @@ void PS3BT::setLedToggle(LED a) { HID_Command(HIDBuffer, HID_BUFFERSIZE); } -void PS3BT::enable_sixaxis() { //Command used to enable the Dualshock 3 and Navigation controller to send data via USB +void PS3BT::enable_sixaxis() { // Command used to enable the Dualshock 3 and Navigation controller to send data via Bluetooth uint8_t cmd_buf[6]; cmd_buf[0] = 0x53; // HID BT Set_report (0x50) | Report Type (Feature 0x03) cmd_buf[1] = 0xF4; // Report ID @@ -623,17 +610,17 @@ void PS3BT::enable_sixaxis() { //Command used to enable the Dualshock 3 and Navi HID_Command(cmd_buf, 6); } -//Playstation Move Controller commands +// Playstation Move Controller commands void PS3BT::HIDMove_Command(uint8_t* data, uint8_t nbytes) { - if (millis() - timerHID <= 250)// Check if is has been less than 200ms since last command - delay((uint32_t)(250 - (millis() - timerHID))); //There have to be a delay between commands + if (millis() - timerHID <= 150)// Check if is has been less than 150ms since last command + delay((uint32_t)(150 - (millis() - timerHID))); // There have to be a delay between commands pBtd->L2CAP_Command(hci_handle, data, nbytes, interrupt_scid[0], interrupt_scid[1]); // The Move controller sends it's data via the intterrupt channel timerHID = millis(); } void PS3BT::moveSetBulb(uint8_t r, uint8_t g, uint8_t b) { //Use this to set the Color using RGB values - //set the Bulb's values into the write buffer + // Set the Bulb's values into the write buffer HIDMoveBuffer[3] = r; HIDMoveBuffer[4] = g; HIDMoveBuffer[5] = b; @@ -650,7 +637,7 @@ void PS3BT::moveSetRumble(uint8_t rumble) { if (rumble < 64 && rumble != 0) // The rumble value has to at least 64, or approximately 25% (64/255*100) Notify(PSTR("\r\nThe rumble value has to at least 64, or approximately 25%"), 0x80); #endif - //set the rumble value into the write buffer + // Set the rumble value into the write buffer HIDMoveBuffer[7] = rumble; HIDMove_Command(HIDMoveBuffer, HID_BUFFERSIZE); diff --git a/PS3BT.h b/PS3BT.h index 5b00232f..6b901402 100644 --- a/PS3BT.h +++ b/PS3BT.h @@ -176,6 +176,10 @@ public: * @param value See: ::LED enum. */ void setLedRaw(uint8_t value); + /** Turn all LEDs off. */ + void setLedOff() { + setLedRaw(0); + } /** * Turn the specific ::LED off. * @param a The ::LED to turn off. diff --git a/PS3USB.cpp b/PS3USB.cpp index 868d7aba..c91e8074 100644 --- a/PS3USB.cpp +++ b/PS3USB.cpp @@ -16,7 +16,7 @@ */ #include "PS3USB.h" -// To enable serial debugging uncomment "#define DEBUG_USB_HOST" in message.h +// To enable serial debugging see "settings.h" //#define EXTRADEBUG // Uncomment to get even more debugging data //#define PRINTREPORT // Uncomment to print the report send by the PS3 Controllers @@ -281,8 +281,7 @@ uint8_t PS3USB::Poll() { #endif } } else if (PS3MoveConnected) { // One can only set the color of the bulb, set the rumble, set and get the bluetooth address and calibrate the magnetometer via USB - if (millis() - timer > 4000) // Send at least every 4th second - { + if (millis() - timer > 4000) { // Send at least every 4th second Move_Command(writeBuf, MOVE_REPORT_BUFFER_SIZE); // The Bulb and rumble values, has to be written again and again, for it to stay turned on timer = millis(); } @@ -291,9 +290,6 @@ uint8_t PS3USB::Poll() { } void PS3USB::readReport() { - if (readBuf == NULL) - return; - ButtonState = (uint32_t)(readBuf[2] | ((uint16_t)readBuf[3] << 8) | ((uint32_t)readBuf[4] << 16)); //Notify(PSTR("\r\nButtonState", 0x80); @@ -305,10 +301,8 @@ void PS3USB::readReport() { } } -void PS3USB::printReport() { //Uncomment "#define PRINTREPORT" to print the report send by the PS3 Controllers +void PS3USB::printReport() { // Uncomment "#define PRINTREPORT" to print the report send by the PS3 Controllers #ifdef PRINTREPORT - if (readBuf == NULL) - return; for (uint8_t i = 0; i < PS3_REPORT_BUFFER_SIZE; i++) { D_PrintHex (readBuf[i], 0x80); Notify(PSTR(" "), 0x80); @@ -324,25 +318,19 @@ bool PS3USB::getButtonPress(Button b) { bool PS3USB::getButtonClick(Button b) { uint32_t button = pgm_read_dword(&BUTTONS[(uint8_t)b]); bool click = (ButtonClickState & button); - ButtonClickState &= ~button; // clear "click" event + ButtonClickState &= ~button; // Clear "click" event return click; } uint8_t PS3USB::getAnalogButton(Button a) { - if (readBuf == NULL) - return 0; return (uint8_t)(readBuf[(pgm_read_byte(&ANALOGBUTTONS[(uint8_t)a])) - 9]); } uint8_t PS3USB::getAnalogHat(AnalogHat a) { - if (readBuf == NULL) - return 0; return (uint8_t)(readBuf[((uint8_t)a + 6)]); } uint16_t PS3USB::getSensor(Sensor a) { - if (readBuf == NULL) - return 0; return ((readBuf[((uint16_t)a) - 9] << 8) | readBuf[((uint16_t)a + 1) - 9]); } @@ -361,23 +349,16 @@ double PS3USB::getAngle(Angle a) { // Convert to 360 degrees resolution // atan2 outputs the value of -π to π (radians) // We are then converting it to 0 to 2π and then to degrees - if (a == Pitch) { - double angle = (atan2(accYval, accZval) + PI) * RAD_TO_DEG; - return angle; - } else { - double angle = (atan2(accXval, accZval) + PI) * RAD_TO_DEG; - return angle; - } + if (a == Pitch) + return (atan2(accYval, accZval) + PI) * RAD_TO_DEG; + else + return (atan2(accXval, accZval) + PI) * RAD_TO_DEG; } else return 0; } bool PS3USB::getStatus(Status c) { - if (readBuf == NULL) - return false; - if (readBuf[((uint16_t)c >> 8) - 9] == ((uint8_t)c & 0xff)) - return true; - return false; + return (readBuf[((uint16_t)c >> 8) - 9] == ((uint8_t)c & 0xff)); } String PS3USB::getStatusString() { @@ -416,8 +397,8 @@ String PS3USB::getStatusString() { } /* Playstation Sixaxis Dualshock and Navigation Controller commands */ -void PS3USB::PS3_Command(uint8_t* data, uint16_t nbytes) { - //bmRequest = Host to device (0x00) | Class (0x20) | Interface (0x01) = 0x21, bRequest = Set Report (0x09), Report ID (0x01), Report Type (Output 0x02), interface (0x00), datalength, datalength, data) +void PS3USB::PS3_Command(uint8_t *data, uint16_t nbytes) { + // bmRequest = Host to device (0x00) | Class (0x20) | Interface (0x01) = 0x21, bRequest = Set Report (0x09), Report ID (0x01), Report Type (Output 0x02), interface (0x00), datalength, datalength, data) pUsb->ctrlReq(bAddress, epInfo[PS3_CONTROL_PIPE].epAddr, bmREQ_HID_OUT, HID_REQUEST_SET_REPORT, 0x01, 0x02, 0x00, nbytes, nbytes, data, NULL); } @@ -430,9 +411,9 @@ void PS3USB::setAllOff() { void PS3USB::setRumbleOff() { writeBuf[1] = 0x00; - writeBuf[2] = 0x00; //low mode off + writeBuf[2] = 0x00; // Low mode off writeBuf[3] = 0x00; - writeBuf[4] = 0x00; //high mode off + writeBuf[4] = 0x00; // High mode off PS3_Command(writeBuf, PS3_REPORT_BUFFER_SIZE); } @@ -476,36 +457,47 @@ void PS3USB::setLedToggle(LED a) { PS3_Command(writeBuf, PS3_REPORT_BUFFER_SIZE); } -void PS3USB::setBdaddr(uint8_t* BDADDR) { - /* Set the internal bluetooth address */ +void PS3USB::setBdaddr(uint8_t *bdaddr) { + /* Set the internal Bluetooth address */ uint8_t buf[8]; buf[0] = 0x01; buf[1] = 0x00; - for (uint8_t i = 0; i < 6; i++) - buf[i + 2] = BDADDR[5 - i]; //Copy into buffer, has to be written reversed - //bmRequest = Host to device (0x00) | Class (0x20) | Interface (0x01) = 0x21, bRequest = Set Report (0x09), Report ID (0xF5), Report Type (Feature 0x03), interface (0x00), datalength, datalength, data) + for (uint8_t i = 0; i < 6; i++) + buf[i + 2] = bdaddr[5 - i]; // Copy into buffer, has to be written reversed, so it is MSB first + + // bmRequest = Host to device (0x00) | Class (0x20) | Interface (0x01) = 0x21, bRequest = Set Report (0x09), Report ID (0xF5), Report Type (Feature 0x03), interface (0x00), datalength, datalength, data pUsb->ctrlReq(bAddress, epInfo[PS3_CONTROL_PIPE].epAddr, bmREQ_HID_OUT, HID_REQUEST_SET_REPORT, 0xF5, 0x03, 0x00, 8, 8, buf, NULL); } -void PS3USB::enable_sixaxis() { //Command used to enable the Dualshock 3 and Navigation controller to send data via USB +void PS3USB::getBdaddr(uint8_t *bdaddr) { + uint8_t buf[8]; + + // bmRequest = Device to host (0x80) | Class (0x20) | Interface (0x01) = 0xA1, bRequest = Get Report (0x01), Report ID (0xF5), Report Type (Feature 0x03), interface (0x00), datalength, datalength, data + pUsb->ctrlReq(bAddress, epInfo[PS3_CONTROL_PIPE].epAddr, bmREQ_HID_IN, HID_REQUEST_GET_REPORT, 0xF5, 0x03, 0x00, 8, 8, buf, NULL); + + for (uint8_t i = 0; i < 6; i++) + bdaddr[5 - i] = buf[i + 2]; // Copy into buffer reversed, so it is LSB first +} + +void PS3USB::enable_sixaxis() { // Command used to enable the Dualshock 3 and Navigation controller to send data via USB uint8_t cmd_buf[4]; cmd_buf[0] = 0x42; // Special PS3 Controller enable commands cmd_buf[1] = 0x0c; cmd_buf[2] = 0x00; cmd_buf[3] = 0x00; - //bmRequest = Host to device (0x00) | Class (0x20) | Interface (0x01) = 0x21, bRequest = Set Report (0x09), Report ID (0xF4), Report Type (Feature 0x03), interface (0x00), datalength, datalength, data) + // bmRequest = Host to device (0x00) | Class (0x20) | Interface (0x01) = 0x21, bRequest = Set Report (0x09), Report ID (0xF4), Report Type (Feature 0x03), interface (0x00), datalength, datalength, data) pUsb->ctrlReq(bAddress, epInfo[PS3_CONTROL_PIPE].epAddr, bmREQ_HID_OUT, HID_REQUEST_SET_REPORT, 0xF4, 0x03, 0x00, 4, 4, cmd_buf, NULL); } /* Playstation Move Controller commands */ -void PS3USB::Move_Command(uint8_t* data, uint16_t nbytes) { +void PS3USB::Move_Command(uint8_t *data, uint16_t nbytes) { pUsb->outTransfer(bAddress, epInfo[ PS3_OUTPUT_PIPE ].epAddr, nbytes, data); } -void PS3USB::moveSetBulb(uint8_t r, uint8_t g, uint8_t b) { //Use this to set the Color using RGB values - // set the Bulb's values into the write buffer +void PS3USB::moveSetBulb(uint8_t r, uint8_t g, uint8_t b) { // Use this to set the Color using RGB values + // Set the Bulb's values into the write buffer writeBuf[2] = r; writeBuf[3] = g; writeBuf[4] = b; @@ -513,7 +505,7 @@ void PS3USB::moveSetBulb(uint8_t r, uint8_t g, uint8_t b) { //Use this to set th Move_Command(writeBuf, MOVE_REPORT_BUFFER_SIZE); } -void PS3USB::moveSetBulb(Colors color) { //Use this to set the Color using the predefined colors in "enums.h" +void PS3USB::moveSetBulb(Colors color) { // Use this to set the Color using the predefined colors in "enums.h" moveSetBulb((uint8_t)(color >> 16), (uint8_t)(color >> 8), (uint8_t)(color)); } @@ -522,14 +514,13 @@ void PS3USB::moveSetRumble(uint8_t rumble) { if (rumble < 64 && rumble != 0) // The rumble value has to at least 64, or approximately 25% (64/255*100) Notify(PSTR("\r\nThe rumble value has to at least 64, or approximately 25%"), 0x80); #endif - //set the rumble value into the write buffer - writeBuf[6] = rumble; + writeBuf[6] = rumble; // Set the rumble value into the write buffer Move_Command(writeBuf, MOVE_REPORT_BUFFER_SIZE); } -void PS3USB::setMoveBdaddr(uint8_t* BDADDR) { - /* Set the internal bluetooth address */ +void PS3USB::setMoveBdaddr(uint8_t *bdaddr) { + /* Set the internal Bluetooth address */ uint8_t buf[11]; buf[0] = 0x05; buf[7] = 0x10; @@ -538,12 +529,34 @@ void PS3USB::setMoveBdaddr(uint8_t* BDADDR) { buf[10] = 0x12; for (uint8_t i = 0; i < 6; i++) - buf[i + 1] = BDADDR[i]; + buf[i + 1] = bdaddr[i]; - //bmRequest = Host to device (0x00) | Class (0x20) | Interface (0x01) = 0x21, bRequest = Set Report (0x09), Report ID (0x05), Report Type (Feature 0x03), interface (0x00), datalength, datalength, data) + // bmRequest = Host to device (0x00) | Class (0x20) | Interface (0x01) = 0x21, bRequest = Set Report (0x09), Report ID (0x05), Report Type (Feature 0x03), interface (0x00), datalength, datalength, data pUsb->ctrlReq(bAddress, epInfo[PS3_CONTROL_PIPE].epAddr, bmREQ_HID_OUT, HID_REQUEST_SET_REPORT, 0x05, 0x03, 0x00, 11, 11, buf, NULL); } +void PS3USB::getMoveBdaddr(uint8_t *bdaddr) { + uint8_t buf[16]; + + // bmRequest = Device to host (0x80) | Class (0x20) | Interface (0x01) = 0xA1, bRequest = Get Report (0x01), Report ID (0x04), Report Type (Feature 0x03), interface (0x00), datalength, datalength, data + pUsb->ctrlReq(bAddress, epInfo[PS3_CONTROL_PIPE].epAddr, bmREQ_HID_IN, HID_REQUEST_GET_REPORT, 0x04, 0x03, 0x00, 16, 16, buf, NULL); + + for (uint8_t i = 0; i < 6; i++) + bdaddr[i] = buf[10 + i]; +} + +void PS3USB::getMoveCalibration(uint8_t *data) { + uint8_t buf[49]; + + for (uint8_t i = 0; i < 3; i++) { + // bmRequest = Device to host (0x80) | Class (0x20) | Interface (0x01) = 0xA1, bRequest = Get Report (0x01), Report ID (0x10), Report Type (Feature 0x03), interface (0x00), datalength, datalength, data + pUsb->ctrlReq(bAddress, epInfo[PS3_CONTROL_PIPE].epAddr, bmREQ_HID_IN, HID_REQUEST_GET_REPORT, 0x10, 0x03, 0x00, 49, 49, buf, NULL); + + for (byte j = 0; j < 49; j++) + data[49 * i + j] = buf[j]; + } +} + void PS3USB::onInit() { if (pFuncOnInit) pFuncOnInit(); // Call the user function diff --git a/PS3USB.h b/PS3USB.h index 775ce56d..ae5314f4 100644 --- a/PS3USB.h +++ b/PS3USB.h @@ -22,27 +22,30 @@ #include "PS3Enums.h" /* PS3 data taken from descriptors */ -#define EP_MAXPKTSIZE 64 // max size for data via USB +#define EP_MAXPKTSIZE 64 // max size for data via USB /* Endpoint types */ -#define EP_INTERRUPT 0x03 +#define EP_INTERRUPT 0x03 /* Names we give to the 3 ps3 pipes - this is only used for setting the bluetooth address into the ps3 controllers */ -#define PS3_CONTROL_PIPE 0 -#define PS3_OUTPUT_PIPE 1 -#define PS3_INPUT_PIPE 2 +#define PS3_CONTROL_PIPE 0 +#define PS3_OUTPUT_PIPE 1 +#define PS3_INPUT_PIPE 2 //PID and VID of the different devices -#define PS3_VID 0x054C // Sony Corporation -#define PS3_PID 0x0268 // PS3 Controller DualShock 3 -#define PS3NAVIGATION_PID 0x042F // Navigation controller -#define PS3MOVE_PID 0x03D5 // Motion controller +#define PS3_VID 0x054C // Sony Corporation +#define PS3_PID 0x0268 // PS3 Controller DualShock 3 +#define PS3NAVIGATION_PID 0x042F // Navigation controller +#define PS3MOVE_PID 0x03D5 // Motion controller -// used in control endpoint header for HID Commands -#define bmREQ_HID_OUT USB_SETUP_HOST_TO_DEVICE|USB_SETUP_TYPE_CLASS|USB_SETUP_RECIPIENT_INTERFACE -#define HID_REQUEST_SET_REPORT 0x09 +// Used in control endpoint header for HID Commands +#define bmREQ_HID_OUT USB_SETUP_HOST_TO_DEVICE|USB_SETUP_TYPE_CLASS|USB_SETUP_RECIPIENT_INTERFACE +#define bmREQ_HID_IN USB_SETUP_DEVICE_TO_HOST|USB_SETUP_TYPE_CLASS|USB_SETUP_RECIPIENT_INTERFACE -#define PS3_MAX_ENDPOINTS 3 +#define HID_REQUEST_GET_REPORT 0x01 +#define HID_REQUEST_SET_REPORT 0x09 + +#define PS3_MAX_ENDPOINTS 3 /** * This class implements support for all the official PS3 Controllers: @@ -112,14 +115,34 @@ public: /** * Used to set the Bluetooth address inside the Dualshock 3 and Navigation controller. - * @param BDADDR Your dongles Bluetooth address. + * Set using LSB first. + * @param bdaddr Your dongles Bluetooth address. */ - void setBdaddr(uint8_t* BDADDR); + void setBdaddr(uint8_t *bdaddr); + /** + * Used to get the Bluetooth address inside the Dualshock 3 and Navigation controller. + * Will return LSB first. + * @param bdaddr Your dongles Bluetooth address. + */ + void getBdaddr(uint8_t *bdaddr); + /** * Used to set the Bluetooth address inside the Move controller. - * @param BDADDR Your dongles Bluetooth address. + * Set using LSB first. + * @param bdaddr Your dongles Bluetooth address. */ - void setMoveBdaddr(uint8_t* BDADDR); + void setMoveBdaddr(uint8_t *bdaddr); + /** + * Used to get the Bluetooth address inside the Move controller. + * Will return LSB first. + * @param bdaddr Your dongles Bluetooth address. + */ + void getMoveBdaddr(uint8_t *bdaddr); + /** + * Used to get the calibration data inside the Move controller. + * @param bdaddr Buffer to store data in. Must be at least 147 bytes + */ + void getMoveCalibration(uint8_t *data); /** @name PS3 Controller functions */ /** @@ -197,6 +220,10 @@ public: * @param value See: ::LED enum. */ void setLedRaw(uint8_t value); + /** Turn all LEDs off. */ + void setLedOff() { + setLedRaw(0); + } /** * Turn the specific ::LED off. * @param a The ::LED to turn off. @@ -278,8 +305,8 @@ private: void printReport(); // print incoming date - Uncomment for debugging /* Private commands */ - void PS3_Command(uint8_t* data, uint16_t nbytes); + void PS3_Command(uint8_t *data, uint16_t nbytes); void enable_sixaxis(); // Command used to enable the Dualshock 3 and Navigation controller to send data via USB - void Move_Command(uint8_t* data, uint16_t nbytes); + void Move_Command(uint8_t *data, uint16_t nbytes); }; #endif diff --git a/README.md b/README.md index 3852db97..361caf1a 100644 --- a/README.md +++ b/README.md @@ -98,7 +98,7 @@ More information can be found at these blog posts: * * -To implement the SPP protocol I used a Bluetooth sniffing tool called [PacketLogger](http://www.tkjelectronics.com/uploads/PacketLogger.zip) developed by Apple. +To implement the SPP protocol I used a Bluetooth sniffing tool called [PacketLogger](http://www.tkjelectronics.com/uploads/PacketLogger.zip) developed by Apple. It enables me to see the Bluetooth communication between my Mac and any device. ### PS3 Library @@ -107,7 +107,7 @@ These libraries consist of the [PS3BT](PS3BT.cpp) and [PS3USB](PS3USB.cpp). Thes In order to use your Playstation controller via Bluetooth you have to set the Bluetooth address of the dongle internally to your PS3 Controller. This can be achieved by plugging the controller in via USB and letting the library set it automatically. -__Note:__ To obtain the address you have to plug in the Bluetooth dongle before connecting the controller, or alternatively you could set it in code like so: . +__Note:__ To obtain the address you have to plug in the Bluetooth dongle before connecting the controller, or alternatively you could set it in code like so: . For more information about the PS3 protocol see the official wiki: . @@ -184,7 +184,7 @@ After that you can simply create the instance like so: WII Wii(&Btd); ``` -Then just press any button any button on the Wiimote and it will connect to the dongle. +Then just press any button on the Wiimote and it will then connect to the dongle. Take a look at the example for more information: . diff --git a/SPP.cpp b/SPP.cpp index 5eba1617..24911da9 100644 --- a/SPP.cpp +++ b/SPP.cpp @@ -16,7 +16,7 @@ */ #include "SPP.h" -// To enable serial debugging uncomment "#define DEBUG_USB_HOST" in message.h +// To enable serial debugging see "settings.h" //#define EXTRADEBUG // Uncomment to get even more debugging data //#define PRINTREPORT // Uncomment to print the report sent to the Arduino @@ -270,19 +270,31 @@ void SPP::ACLData(uint8_t* l2capinbuf) { /* Read the incoming message */ if (rfcommChannelType == RFCOMM_UIH && rfcommChannel == rfcommChannelConnection) { uint8_t length = l2capinbuf[10] >> 1; // Get length - uint8_t offset = l2capinbuf[4] - length - 4; // See if there is credit - if (rfcommAvailable + length <= sizeof (rfcommDataBuffer)) { // Don't add data to buffer if it would be full - for (uint8_t i = 0; i < length; i++) + uint8_t offset = l2capinbuf[4] - length - 4; // Check if there is credit + if (checkFcs(&l2capinbuf[8], l2capinbuf[11 + length + offset])) { + uint8_t i = 0; + for (; i < length; i++) { + if (rfcommAvailable + i >= sizeof (rfcommDataBuffer)) { +#ifdef DEBUG_USB_HOST + Notify(PSTR("\r\nWarning: Buffer is full!"), 0x80); +#endif + break; + } rfcommDataBuffer[rfcommAvailable + i] = l2capinbuf[11 + i + offset]; - rfcommAvailable += length; - } + } + rfcommAvailable += i; #ifdef EXTRADEBUG - Notify(PSTR("\r\nRFCOMM Data Available: "), 0x80); - Notify(rfcommAvailable, 0x80); - if (offset) { - Notify(PSTR(" - Credit: 0x"), 0x80); - D_PrintHex (l2capinbuf[11], 0x80); + Notify(PSTR("\r\nRFCOMM Data Available: "), 0x80); + Notify(rfcommAvailable, 0x80); + if (offset) { + Notify(PSTR(" - Credit: 0x"), 0x80); + D_PrintHex (l2capinbuf[11], 0x80); + } +#endif } +#ifdef DEBUG_USB_HOST + else + Notify(PSTR("\r\nError in FCS checksum!"), 0x80); #endif #ifdef PRINTREPORT // Uncomment "#define PRINTREPORT" to print the report send to the Arduino via Bluetooth for (uint8_t i = 0; i < length; i++) @@ -723,16 +735,24 @@ void SPP::sendRfcommCredit(uint8_t channel, uint8_t direction, uint8_t CR, uint8 } /* CRC on 2 bytes */ -uint8_t SPP::__crc(uint8_t* data) { - return (pgm_read_byte(&rfcomm_crc_table[pgm_read_byte(&rfcomm_crc_table[0xff ^ data[0]]) ^ data[1]])); +uint8_t SPP::crc(uint8_t *data) { + return (pgm_read_byte(&rfcomm_crc_table[pgm_read_byte(&rfcomm_crc_table[0xFF ^ data[0]]) ^ data[1]])); } -/* Calculate FCS - we never actually check if the host sends correct FCS to the Arduino */ +/* Calculate FCS */ uint8_t SPP::calcFcs(uint8_t *data) { if ((data[1] & 0xEF) == RFCOMM_UIH) - return (0xff - __crc(data)); // FCS on 2 bytes + return (0xFF - crc(data)); // FCS on 2 bytes else - return (0xff - pgm_read_byte(&rfcomm_crc_table[__crc(data) ^ data[2]])); // FCS on 3 bytes + return (0xFF - pgm_read_byte(&rfcomm_crc_table[crc(data) ^ data[2]])); // FCS on 3 bytes +} + +/* Check FCS */ +bool SPP::checkFcs(uint8_t *data, uint8_t fcs) { + uint8_t temp = crc(data); + if ((data[1] & 0xEF) != RFCOMM_UIH) + temp = pgm_read_byte(&rfcomm_crc_table[temp ^ data[2]]); // FCS on 3 bytes + return (pgm_read_byte(&rfcomm_crc_table[temp ^ fcs]) == 0xCF); } /* Serial commands */ @@ -740,7 +760,7 @@ size_t SPP::write(uint8_t data) { return write(&data,1); } -size_t SPP::write(const uint8_t* data, size_t size) { +size_t SPP::write(const uint8_t *data, size_t size) { for(uint8_t i = 0; i < size; i++) { if(sppIndex >= sizeof(sppOutputBuffer)/sizeof(sppOutputBuffer[0])) send(); // Send the current data in the buffer diff --git a/SPP.h b/SPP.h index 7a4f90e0..558f16bc 100644 --- a/SPP.h +++ b/SPP.h @@ -215,7 +215,7 @@ private: void RFCOMM_task(); // RFCOMM state machine /* SDP Commands */ - void SDP_Command(uint8_t* data, uint8_t nbytes); + void SDP_Command(uint8_t *data, uint8_t nbytes); void serviceNotSupported(uint8_t transactionIDHigh, uint8_t transactionIDLow); void serialPortResponse1(uint8_t transactionIDHigh, uint8_t transactionIDLow); void serialPortResponse2(uint8_t transactionIDHigh, uint8_t transactionIDLow); @@ -223,10 +223,11 @@ private: void l2capResponse2(uint8_t transactionIDHigh, uint8_t transactionIDLow); /* RFCOMM Commands */ - void RFCOMM_Command(uint8_t* data, uint8_t nbytes); - void sendRfcomm(uint8_t channel, uint8_t direction, uint8_t CR, uint8_t channelType, uint8_t pfBit, uint8_t* data, uint8_t length); + void RFCOMM_Command(uint8_t *data, uint8_t nbytes); + void sendRfcomm(uint8_t channel, uint8_t direction, uint8_t CR, uint8_t channelType, uint8_t pfBit, uint8_t *data, uint8_t length); void sendRfcommCredit(uint8_t channel, uint8_t direction, uint8_t CR, uint8_t channelType, uint8_t pfBit, uint8_t credit); uint8_t calcFcs(uint8_t *data); - uint8_t __crc(uint8_t* data); + bool checkFcs(uint8_t *data, uint8_t fcs); + uint8_t crc(uint8_t *data); }; #endif \ No newline at end of file diff --git a/Usb.cpp b/Usb.cpp index 4e4fde61..f8c8edae 100644 --- a/Usb.cpp +++ b/Usb.cpp @@ -567,6 +567,7 @@ uint8_t USB::DefaultAddressing(uint8_t parent, uint8_t port, bool lowspeed) { uint8_t USB::AttemptConfig(uint8_t driver, uint8_t parent, uint8_t port, bool lowspeed) { //printf("AttemptConfig: parent = %i, port = %i\r\n", parent, port); + uint8_t retries = 0; again: uint8_t rcode = devConfig[driver]->ConfigureDevice(parent, port, lowspeed); @@ -579,15 +580,17 @@ again: // reset parent port devConfig[parent]->ResetHubPort(port); } - } else if (rcode == hrJERR) { // Some devices returns this when plugged in - trying to initialize the device again usually works + } else if (rcode == hrJERR && retries < 3) { // Some devices returns this when plugged in - trying to initialize the device again usually works delay(100); + retries++; goto again; } else if (rcode) return rcode; rcode = devConfig[driver]->Init(parent, port, lowspeed); - if (rcode == hrJERR) { // Some devices returns this when plugged in - trying to initialize the device again usually works + if (rcode == hrJERR && retries < 3) { // Some devices returns this when plugged in - trying to initialize the device again usually works delay(100); + retries++; goto again; } if (rcode) { diff --git a/Wii.cpp b/Wii.cpp index 0689f43c..2e8669db 100755 --- a/Wii.cpp +++ b/Wii.cpp @@ -18,7 +18,7 @@ */ #include "Wii.h" -// To enable serial debugging uncomment "#define DEBUG_USB_HOST" in message.h +// To enable serial debugging see "settings.h" //#define EXTRADEBUG // Uncomment to get even more debugging data //#define PRINTREPORT // Uncomment to print the report send by the Wii controllers @@ -473,11 +473,11 @@ void WII::ACLData(uint8_t* l2capinbuf) { pitchGyroSpeed = (double)gyroPitchRaw / ((double)gyroPitchZero / pitchGyroScale); /* The onboard gyro has two ranges for slow and fast mode */ - if (!(l2capinbuf[18] & 0x02)) // Check if fast more is used + if (!(l2capinbuf[18] & 0x02)) // Check if fast mode is used yawGyroSpeed *= 4.545; - if (!(l2capinbuf[18] & 0x01)) // Check if fast more is used + if (!(l2capinbuf[18] & 0x01)) // Check if fast mode is used pitchGyroSpeed *= 4.545; - if (!(l2capinbuf[19] & 0x02)) // Check if fast more is used + if (!(l2capinbuf[19] & 0x02)) // Check if fast mode is used rollGyroSpeed *= 4.545; compPitch = (0.93 * (compPitch + (pitchGyroSpeed * (double)(micros() - timer) / 1000000)))+(0.07 * getWiimotePitch()); // Use a complimentary filter to calculate the angle diff --git a/Wii.h b/Wii.h index f1ba6a90..f8d206ef 100755 --- a/Wii.h +++ b/Wii.h @@ -191,6 +191,10 @@ public: * @param value See: ::LED enum. */ void setLedRaw(uint8_t value); + /** Turn all LEDs off. */ + void setLedOff() { + setLedRaw(0); + } /** * Turn the specific ::LED off. * @param a The ::LED to turn off. @@ -210,9 +214,7 @@ public: * This will set the LEDs, so the user can see which connections are active. * * The first ::LED indicate that the Wiimote is connected, - * * the second ::LED indicate indicate that a Motion Plus is also connected - * * the third ::LED will indicate that a Nunchuck controller is also connected. */ void setLedStatus(); diff --git a/WiiCameraReadme.md b/WiiCameraReadme.md index d9bcb78a..d3fc11ae 100644 --- a/WiiCameraReadme.md +++ b/WiiCameraReadme.md @@ -1,8 +1,6 @@ Please see for the complete capabilities of the Wii camera. The IR camera code was written based on the above website and with support from Kristian Lauszus. -Must omit the "." in the name of the USB\_Host\_Shiled\_2.0 library folder when inserting into the Arudino library folder. - -This library is large, if you run into memory problems when uploading to the Arduino, comment out the \#define DEBUG in the BTD.cpp and Wii.cpp files. +This library is large, if you run into memory problems when uploading to the Arduino, disable serial debugging. To enable the IR camera code, uncomment \#define WIICAMERA in Wii.h. diff --git a/XBOXOLD.cpp b/XBOXOLD.cpp index 34c80b67..f82efc0c 100644 --- a/XBOXOLD.cpp +++ b/XBOXOLD.cpp @@ -16,7 +16,7 @@ */ #include "XBOXOLD.h" -// To enable serial debugging uncomment "#define DEBUG_USB_HOST" in message.h +// To enable serial debugging see "settings.h" //#define EXTRADEBUG // Uncomment to get even more debugging data //#define PRINTREPORT // Uncomment to print the report send by the Xbox controller @@ -291,15 +291,15 @@ void XBOXOLD::printReport(uint16_t length) { //Uncomment "#define PRINTREPORT" t } uint8_t XBOXOLD::getButtonPress(Button b) { + uint8_t button = pgm_read_byte(&XBOXOLDBUTTONS[(uint8_t)b]); if (b == A || b == B || b == X || b == Y || b == BLACK || b == WHITE || b == L1 || b == R1) // A, B, X, Y, BLACK, WHITE, L1, and R1 are analog buttons - return buttonValues[pgm_read_byte(&XBOXOLDBUTTONS[(uint8_t)b])]; // Analog buttons - return (ButtonState & pgm_read_byte(&XBOXOLDBUTTONS[(uint8_t)b])); // Digital buttons + return buttonValues[button]; // Analog buttons + return (ButtonState & button); // Digital buttons } bool XBOXOLD::getButtonClick(Button b) { - uint8_t button; + uint8_t button = pgm_read_byte(&XBOXOLDBUTTONS[(uint8_t)b]); if (b == A || b == B || b == X || b == Y || b == BLACK || b == WHITE || b == L1 || b == R1) { // A, B, X, Y, BLACK, WHITE, L1, and R1 are analog buttons - button = pgm_read_byte(&XBOXOLDBUTTONS[(uint8_t)b]); if (buttonClicked[button]) { buttonClicked[button] = false; return true; @@ -307,7 +307,6 @@ bool XBOXOLD::getButtonClick(Button b) { return false; } - button = pgm_read_byte(&XBOXOLDBUTTONS[(uint8_t)b]); // Digital buttons bool click = (ButtonClickState & button); ButtonClickState &= ~button; // clear "click" event return click; diff --git a/XBOXRECV.cpp b/XBOXRECV.cpp index c011dc34..07963c52 100644 --- a/XBOXRECV.cpp +++ b/XBOXRECV.cpp @@ -18,7 +18,7 @@ */ #include "XBOXRECV.h" -// To enable serial debugging uncomment "#define DEBUG_USB_HOST" in message.h +// To enable serial debugging see "settings.h" //#define EXTRADEBUG // Uncomment to get even more debugging data //#define PRINTREPORT // Uncomment to print the report send by the Xbox 360 Controller @@ -37,30 +37,28 @@ bPollEnable(false) { // don't start polling before dongle is connected pUsb->RegisterDeviceClass(this); //set devConfig[] entry } -uint8_t XBOXRECV::Init(uint8_t parent, uint8_t port, bool lowspeed) { - uint8_t buf[sizeof (USB_DEVICE_DESCRIPTOR)]; +uint8_t XBOXRECV::ConfigureDevice(uint8_t parent, uint8_t port, bool lowspeed) { + const uint8_t constBufSize = sizeof (USB_DEVICE_DESCRIPTOR); + uint8_t buf[constBufSize]; USB_DEVICE_DESCRIPTOR * udd = reinterpret_cast(buf); uint8_t rcode; UsbDevice *p = NULL; EpInfo *oldep_ptr = NULL; - uint16_t PID; - uint16_t VID; + uint16_t PID, VID; - // get memory address of USB device address pool - AddressPool &addrPool = pUsb->GetAddressPool(); + AddressPool &addrPool = pUsb->GetAddressPool(); // Get memory address of USB device address pool #ifdef EXTRADEBUG Notify(PSTR("\r\nXBOXRECV Init"), 0x80); #endif - // check if address has already been assigned to an instance - if (bAddress) { + + if (bAddress) { // Check if address has already been assigned to an instance #ifdef DEBUG_USB_HOST Notify(PSTR("\r\nAddress in use"), 0x80); #endif return USB_ERROR_CLASS_INSTANCE_ALREADY_IN_USE; } - // Get pointer to pseudo device with address 0 assigned - p = addrPool.GetUsbDevicePtr(0); + p = addrPool.GetUsbDevicePtr(0); // Get pointer to pseudo device with address 0 assigned if (!p) { #ifdef DEBUG_USB_HOST @@ -76,18 +74,13 @@ uint8_t XBOXRECV::Init(uint8_t parent, uint8_t port, bool lowspeed) { return USB_ERROR_EPINFO_IS_NULL; } - // Save old pointer to EP_RECORD of address 0 - oldep_ptr = p->epinfo; - - // Temporary assign new pointer to epInfo to p->epinfo in order to avoid toggle inconsistence - p->epinfo = epInfo; - + oldep_ptr = p->epinfo; // Save old pointer to EP_RECORD of address 0 + p->epinfo = epInfo; // Temporary assign new pointer to epInfo to p->epinfo in order to avoid toggle inconsistence p->lowspeed = lowspeed; - // Get device descriptor - rcode = pUsb->getDevDescr(0, 0, sizeof (USB_DEVICE_DESCRIPTOR), (uint8_t*)buf); // Get device descriptor - addr, ep, nbytes, data - // Restore p->epinfo - p->epinfo = oldep_ptr; + rcode = pUsb->getDevDescr(0, 0, constBufSize, (uint8_t*)buf); // Get device descriptor - addr, ep, nbytes, data + + p->epinfo = oldep_ptr; // Restore p->epinfo if (rcode) goto FailGetDevDescr; @@ -95,53 +88,101 @@ uint8_t XBOXRECV::Init(uint8_t parent, uint8_t port, bool lowspeed) { VID = udd->idVendor; PID = udd->idProduct; - if (VID != XBOX_VID && VID != MADCATZ_VID) // We just check if it's a Xbox receiver using the Vendor ID - goto FailUnknownDevice; - else if (PID != XBOX_WIRELESS_RECEIVER_PID && PID != XBOX_WIRELESS_RECEIVER_THIRD_PARTY_PID) { // Check the PID as well + if ((VID != XBOX_VID && VID != MADCATZ_VID) || (PID != XBOX_WIRELESS_RECEIVER_PID && PID != XBOX_WIRELESS_RECEIVER_THIRD_PARTY_PID)) { // Check if it's a Xbox receiver using the Vendor ID and Product ID #ifdef DEBUG_USB_HOST Notify(PSTR("\r\nYou'll need a wireless receiver for this libary to work"), 0x80); #endif goto FailUnknownDevice; } - // Allocate new address according to device class - bAddress = addrPool.AllocAddress(parent, false, port); + bAddress = addrPool.AllocAddress(parent, false, port); // Allocate new address according to device class - if (!bAddress) + if (!bAddress) { +#ifdef DEBUG_USB_HOST + Notify(PSTR("\r\nOut of address space"), 0x80); +#endif return USB_ERROR_OUT_OF_ADDRESS_SPACE_IN_POOL; + } // Extract Max Packet Size from device descriptor epInfo[0].maxPktSize = udd->bMaxPacketSize0; + epInfo[1].epAddr = udd->bNumConfigurations; // Steal and abuse from epInfo structure to save memory - // Assign new address to the device - rcode = pUsb->setAddr(0, 0, bAddress); + delay(20); // Wait a little before resetting device + + return USB_ERROR_CONFIG_REQUIRES_ADDITIONAL_RESET; + + /* Diagnostic messages */ +FailGetDevDescr: +#ifdef DEBUG_USB_HOST + NotifyFailGetDevDescr(rcode); +#endif + if (rcode != hrJERR) + rcode = USB_ERROR_FailGetDevDescr; + goto Fail; + +FailUnknownDevice: +#ifdef DEBUG_USB_HOST + NotifyFailUnknownDevice(VID,PID); +#endif + rcode = USB_DEV_CONFIG_ERROR_DEVICE_NOT_SUPPORTED; + +Fail: +#ifdef DEBUG_USB_HOST + Notify(PSTR("\r\nXbox 360 Init Failed, error code: "), 0x80); + NotifyFail(rcode); +#endif + Release(); + return rcode; +}; + +uint8_t XBOXRECV::Init(uint8_t parent, uint8_t port, bool lowspeed) { + uint8_t rcode; + uint8_t num_of_conf = epInfo[1].epAddr; // Number of configurations + epInfo[1].epAddr = 0; + + AddressPool &addrPool = pUsb->GetAddressPool(); +#ifdef EXTRADEBUG + Notify(PSTR("\r\nBTD Init"), 0x80); +#endif + UsbDevice *p = addrPool.GetUsbDevicePtr(bAddress); // Get pointer to assigned address record + + if (!p) { +#ifdef DEBUG_USB_HOST + Notify(PSTR("\r\nAddress not found"), 0x80); +#endif + return USB_ERROR_ADDRESS_NOT_FOUND_IN_POOL; + } + + delay(300); // Assign new address to the device + + rcode = pUsb->setAddr(0, 0, bAddress); // Assign new address to the device if (rcode) { - p->lowspeed = false; - addrPool.FreeAddress(bAddress); - bAddress = 0; #ifdef DEBUG_USB_HOST Notify(PSTR("\r\nsetAddr: "), 0x80); D_PrintHex (rcode, 0x80); #endif - return rcode; + p->lowspeed = false; + goto Fail; } #ifdef EXTRADEBUG Notify(PSTR("\r\nAddr: "), 0x80); D_PrintHex (bAddress, 0x80); #endif - delay(300); // Spec says you should wait at least 200ms p->lowspeed = false; - //get pointer to assigned address record - p = addrPool.GetUsbDevicePtr(bAddress); - if (!p) + p = addrPool.GetUsbDevicePtr(bAddress); // Get pointer to assigned address record + if (!p) { +#ifdef DEBUG_USB_HOST + Notify(PSTR("\r\nAddress not found"), 0x80); +#endif return USB_ERROR_ADDRESS_NOT_FOUND_IN_POOL; + } p->lowspeed = lowspeed; - // Assign epInfo to epinfo pointer - only EP0 is known - rcode = pUsb->setEpInfoEntry(bAddress, 1, epInfo); + rcode = pUsb->setEpInfoEntry(bAddress, 1, epInfo); // Assign epInfo to epinfo pointer - only EP0 is known if (rcode) goto FailSetDevTblEntry; @@ -217,9 +258,10 @@ uint8_t XBOXRECV::Init(uint8_t parent, uint8_t port, bool lowspeed) { #endif XboxReceiverConnected = true; bPollEnable = true; - return 0; // successful configuration + checkStatusTimer = 0; // Reset timer + return 0; // Successful configuration - /* diagnostic messages */ + /* Diagnostic messages */ FailGetDevDescr: #ifdef DEBUG_USB_HOST NotifyFailGetDevDescr(); @@ -243,8 +285,8 @@ FailUnknownDevice: #endif rcode = USB_DEV_CONFIG_ERROR_DEVICE_NOT_SUPPORTED; -#ifdef DEBUG_USB_HOST Fail: +#ifdef DEBUG_USB_HOST Notify(PSTR("\r\nXbox 360 Init Failed, error code: "), 0x80); NotifyFail(rcode); #endif @@ -266,23 +308,23 @@ uint8_t XBOXRECV::Release() { uint8_t XBOXRECV::Poll() { if (!bPollEnable) return 0; - if (!timer || ((millis() - timer) > 3000)) { // Run checkStatus every 3 seconds - timer = millis(); + if (!checkStatusTimer || ((millis() - checkStatusTimer) > 3000)) { // Run checkStatus every 3 seconds + checkStatusTimer = millis(); checkStatus(); } + uint8_t inputPipe; uint16_t bufferSize; for (uint8_t i = 0; i < 4; i++) { - switch (i) { - case 0: inputPipe = XBOX_INPUT_PIPE_1; - break; - case 1: inputPipe = XBOX_INPUT_PIPE_2; - break; - case 2: inputPipe = XBOX_INPUT_PIPE_3; - break; - case 3: inputPipe = XBOX_INPUT_PIPE_4; - break; - } + if (i == 0) + inputPipe = XBOX_INPUT_PIPE_1; + else if (i == 1) + inputPipe = XBOX_INPUT_PIPE_2; + else if (i == 2) + inputPipe = XBOX_INPUT_PIPE_3; + else + inputPipe = XBOX_INPUT_PIPE_4; + bufferSize = EP_MAXPKTSIZE; // This is the maximum number of bytes we want to receive pUsb->inTransfer(bAddress, epInfo[ inputPipe ].epAddr, &bufferSize, readBuf); if (bufferSize > 0) { // The number of received bytes @@ -420,22 +462,22 @@ bool XBOXRECV::buttonChanged(uint8_t controller) { /* ControllerStatus Breakdown - ControllerStatus[controller] & 0x0001 // 0 - ControllerStatus[controller] & 0x0002 // normal batteries, no rechargeable battery pack - ControllerStatus[controller] & 0x0004 // controller starting up / settling - ControllerStatus[controller] & 0x0008 // headset adapter plugged in, but no headphones connected (mute?) - ControllerStatus[controller] & 0x0010 // 0 - ControllerStatus[controller] & 0x0020 // 1 - ControllerStatus[controller] & 0x0040 // battery level (high bit) - ControllerStatus[controller] & 0x0080 // battery level (low bit) - ControllerStatus[controller] & 0x0100 // 1 - ControllerStatus[controller] & 0x0200 // 1 - ControllerStatus[controller] & 0x0400 // headset adapter plugged in - ControllerStatus[controller] & 0x0800 // 0 - ControllerStatus[controller] & 0x1000 // 1 - ControllerStatus[controller] & 0x2000 // 0 - ControllerStatus[controller] & 0x4000 // 0 - ControllerStatus[controller] & 0x8000 // 0 +ControllerStatus[controller] & 0x0001 // 0 +ControllerStatus[controller] & 0x0002 // normal batteries, no rechargeable battery pack +ControllerStatus[controller] & 0x0004 // controller starting up / settling +ControllerStatus[controller] & 0x0008 // headset adapter plugged in, but no headphones connected (mute?) +ControllerStatus[controller] & 0x0010 // 0 +ControllerStatus[controller] & 0x0020 // 1 +ControllerStatus[controller] & 0x0040 // battery level (high bit) +ControllerStatus[controller] & 0x0080 // battery level (low bit) +ControllerStatus[controller] & 0x0100 // 1 +ControllerStatus[controller] & 0x0200 // 1 +ControllerStatus[controller] & 0x0400 // headset adapter plugged in +ControllerStatus[controller] & 0x0800 // 0 +ControllerStatus[controller] & 0x1000 // 1 +ControllerStatus[controller] & 0x2000 // 0 +ControllerStatus[controller] & 0x4000 // 0 +ControllerStatus[controller] & 0x8000 // 0 */ uint8_t XBOXRECV::getBatteryLevel(uint8_t controller) { return ((controllerStatus[controller] & 0x00C0) >> 6); @@ -468,6 +510,15 @@ void XBOXRECV::XboxCommand(uint8_t controller, uint8_t* data, uint16_t nbytes) { #endif } +void XBOXRECV::disconnect(uint8_t controller) { + writeBuf[0] = 0x00; + writeBuf[1] = 0x00; + writeBuf[2] = 0x08; + writeBuf[3] = 0xC0; + + XboxCommand(controller, writeBuf, 4); +} + void XBOXRECV::setLedRaw(uint8_t value, uint8_t controller) { writeBuf[0] = 0x00; writeBuf[1] = 0x00; diff --git a/XBOXRECV.h b/XBOXRECV.h index c5a7f147..eee75cda 100644 --- a/XBOXRECV.h +++ b/XBOXRECV.h @@ -64,6 +64,14 @@ public: XBOXRECV(USB *pUsb); /** @name USBDeviceConfig implementation */ + /** + * Address assignment and basic initilization is done here. + * @param parent Hub number. + * @param port Port number on the hub. + * @param lowspeed Speed of the device. + * @return 0 on success. + */ + virtual uint8_t ConfigureDevice(uint8_t parent, uint8_t port, bool lowspeed); /** * Initialize the Xbox wireless receiver. * @param parent Hub number. @@ -136,6 +144,12 @@ public: */ int16_t getAnalogHat(AnalogHat a, uint8_t controller = 0); + /** + * Used to disconnect any of the controllers. + * @param controller The controller to disconnect. Default to 0. + */ + void disconnect(uint8_t controller = 0); + /** * Turn rumble off and all the LEDs on the specific controller. * @param controller The controller to write to. Default to 0. @@ -251,7 +265,7 @@ private: bool L2Clicked[4]; // These buttons are analog, so we use we use these bools to check if they where clicked or not bool R2Clicked[4]; - unsigned long timer; // Timing for checkStatus() signals + uint32_t checkStatusTimer; // Timing for checkStatus() signals uint8_t readBuf[EP_MAXPKTSIZE]; // General purpose buffer for input data uint8_t writeBuf[7]; // General purpose buffer for output data diff --git a/XBOXUSB.cpp b/XBOXUSB.cpp index 2bac3152..2228af7e 100644 --- a/XBOXUSB.cpp +++ b/XBOXUSB.cpp @@ -16,7 +16,7 @@ */ #include "XBOXUSB.h" -// To enable serial debugging uncomment "#define DEBUG_USB_HOST" in message.h +// To enable serial debugging see "settings.h" //#define EXTRADEBUG // Uncomment to get even more debugging data //#define PRINTREPORT // Uncomment to print the report send by the Xbox 360 Controller @@ -283,7 +283,7 @@ uint8_t XBOXUSB::getButtonPress(Button b) { return (uint8_t)(ButtonState >> 8); else if (b == R2) return (uint8_t)ButtonState; - return (ButtonState & ((uint32_t)pgm_read_word(&XBOXBUTTONS[(uint8_t)b]) << 16)); + return (bool)(ButtonState & ((uint32_t)pgm_read_word(&XBOXBUTTONS[(uint8_t)b]) << 16)); } bool XBOXUSB::getButtonClick(Button b) { diff --git a/adk.cpp b/adk.cpp index ef59c052..63427b26 100644 --- a/adk.cpp +++ b/adk.cpp @@ -13,7 +13,7 @@ Contact information Circuits At Home, LTD Web : http://www.circuitsathome.com e-mail : support@circuitsathome.com - */ +*/ /* Google ADK interface */ @@ -30,7 +30,6 @@ ADK::ADK(USB *p, const char* manufacturer, const char* serial) : /* ADK ID Strings */ - manufacturer(manufacturer), model(model), description(description), @@ -46,12 +45,10 @@ ready(false) { for (uint8_t i = 0; i < ADK_MAX_ENDPOINTS; i++) { epInfo[i].epAddr = 0; epInfo[i].maxPktSize = (i) ? 0 : 8; - epInfo[i].epAttribs = (0xfc & (USB_NAK_MAX_POWER << 2)); + epInfo[i].epAttribs = 0; + epInfo[i].bmNakPower = (i) ? USB_NAK_NOWAIT : USB_NAK_MAX_POWER; }//for(uint8_t i=0; iRegisterDeviceClass(this); //set devConfig[] entry @@ -64,7 +61,6 @@ uint8_t ADK::ConfigureDevice(uint8_t parent, uint8_t port, bool lowspeed) { /* Connection initialization of an Android phone */ uint8_t ADK::Init(uint8_t parent, uint8_t port, bool lowspeed) { - uint8_t buf[sizeof (USB_DEVICE_DESCRIPTOR)]; USB_DEVICE_DESCRIPTOR * udd = reinterpret_cast(buf); uint8_t rcode; @@ -119,6 +115,7 @@ uint8_t ADK::Init(uint8_t parent, uint8_t port, bool lowspeed) { // Extract Max Packet Size from device descriptor epInfo[0].maxPktSize = udd->bMaxPacketSize0; + // Assign new address to the device rcode = pUsb->setAddr(0, 0, bAddress); if (rcode) { @@ -157,10 +154,18 @@ uint8_t ADK::Init(uint8_t parent, uint8_t port, bool lowspeed) { num_of_conf = udd->bNumConfigurations; //USBTRACE2("\r\nNC:",num_of_conf); - for (uint8_t i = 0; i < num_of_conf; i++) { ConfigDescParser < 0, 0, 0, 0 > confDescrParser(this); + delay(1); rcode = pUsb->getConfDescr(bAddress, 0, i, &confDescrParser); +#if defined(XOOM) + //added by Jaylen Scott Vanorden + if (rcode) { + USBTRACE2("\r\nGot 1st bad code for config: ", rcode); + // Try once more + rcode = pUsb->getConfDescr(bAddress, 0, i, &confDescrParser); + } +#endif if (rcode) { goto FailGetConfDescr; } @@ -177,27 +182,27 @@ uint8_t ADK::Init(uint8_t parent, uint8_t port, bool lowspeed) { } } - - // Set Configuration Value rcode = pUsb->setConf(bAddress, 0, bConfNum); if (rcode) { goto FailSetConfDescr; } /* print endpoint structure */ - // USBTRACE("\r\nEndpoint Structure:"); - // USBTRACE("\r\nEP0:"); - // USBTRACE2("\r\nAddr: ", epInfo[0].epAddr ); - // USBTRACE2("\r\nMax.pkt.size: ", epInfo[0].maxPktSize ); - // USBTRACE2("\r\nAttr: ", epInfo[0].epAttribs ); - // USBTRACE("\r\nEpout:"); - // USBTRACE2("\r\nAddr: ", epInfo[epDataOutIndex].epAddr ); - // USBTRACE2("\r\nMax.pkt.size: ", epInfo[epDataOutIndex].maxPktSize ); - // USBTRACE2("\r\nAttr: ", epInfo[epDataOutIndex].epAttribs ); - // USBTRACE("\r\nEpin:"); - // USBTRACE2("\r\nAddr: ", epInfo[epDataInIndex].epAddr ); - // USBTRACE2("\r\nMax.pkt.size: ", epInfo[epDataInIndex].maxPktSize ); - // USBTRACE2("\r\nAttr: ", epInfo[epDataInIndex].epAttribs ); + /* + USBTRACE("\r\nEndpoint Structure:"); + USBTRACE("\r\nEP0:"); + USBTRACE2("\r\nAddr: ", epInfo[0].epAddr); + USBTRACE2("\r\nMax.pkt.size: ", epInfo[0].maxPktSize); + USBTRACE2("\r\nAttr: ", epInfo[0].epAttribs); + USBTRACE("\r\nEpout:"); + USBTRACE2("\r\nAddr: ", epInfo[epDataOutIndex].epAddr); + USBTRACE2("\r\nMax.pkt.size: ", epInfo[epDataOutIndex].maxPktSize); + USBTRACE2("\r\nAttr: ", epInfo[epDataOutIndex].epAttribs); + USBTRACE("\r\nEpin:"); + USBTRACE2("\r\nAddr: ", epInfo[epDataInIndex].epAddr); + USBTRACE2("\r\nMax.pkt.size: ", epInfo[epDataInIndex].maxPktSize); + USBTRACE2("\r\nAttr: ", epInfo[epDataInIndex].epAttribs); + */ USBTRACE("\r\nConfiguration successful"); ready = true; @@ -207,7 +212,16 @@ uint8_t ADK::Init(uint8_t parent, uint8_t port, bool lowspeed) { //probe device - get accessory protocol revision { uint16_t adkproto = -1; + delay(1); rcode = getProto((uint8_t*) & adkproto); +#if defined(XOOM) + //added by Jaylen Scott Vanorden + if (rcode) { + USBTRACE2("\r\nGot 1st bad code for proto: ", rcode); + // Try once more + rcode = getProto((uint8_t*) & adkproto); + } +#endif if (rcode) { goto FailGetProto; //init fails } @@ -269,7 +283,7 @@ FailSwAcc: goto Fail; #endif - //FailOnInit: +//FailOnInit: // USBTRACE("OnInit:"); // goto Fail; // @@ -286,9 +300,9 @@ Fail: /* Extracts bulk-IN and bulk-OUT endpoint information from config descriptor */ void ADK::EndpointXtract(uint8_t conf, uint8_t iface, uint8_t alt, uint8_t proto, const USB_ENDPOINT_DESCRIPTOR *pep) { - //ErrorMessage(PSTR("Conf.Val"), conf); - //ErrorMessage(PSTR("Iface Num"),iface); - //ErrorMessage(PSTR("Alt.Set"), alt); + //ErrorMessage(PSTR("Conf.Val"), conf); + //ErrorMessage(PSTR("Iface Num"), iface); + //ErrorMessage(PSTR("Alt.Set"), alt); //added by Yuuichi Akagawa if (bNumEP == 3) { @@ -297,19 +311,16 @@ void ADK::EndpointXtract(uint8_t conf, uint8_t iface, uint8_t alt, uint8_t proto bConfNum = conf; - uint8_t index; + if ((pep->bmAttributes & 0x02) == 2) { + uint8_t index = ((pep->bEndpointAddress & 0x80) == 0x80) ? epDataInIndex : epDataOutIndex; + // Fill in the endpoint info structure + epInfo[index].epAddr = (pep->bEndpointAddress & 0x0F); + epInfo[index].maxPktSize = (uint8_t)pep->wMaxPacketSize; - // if ((pep->bmAttributes & 0x02) == 2) { - index = ((pep->bEndpointAddress & 0x80) == 0x80) ? epDataInIndex : epDataOutIndex; - // } + bNumEP++; - // Fill in the endpoint info structure - epInfo[index].epAddr = (pep->bEndpointAddress & 0x0F); - epInfo[index].maxPktSize = (uint8_t)pep->wMaxPacketSize; - - bNumEP++; - - //PrintEndpointDescriptor(pep); + //PrintEndpointDescriptor(pep); + } } /* Performs a cleanup after failed Init() attempt */ diff --git a/adk.h b/adk.h index 604cb02a..ab5ed38f 100644 --- a/adk.h +++ b/adk.h @@ -13,7 +13,7 @@ Contact information Circuits At Home, LTD Web : http://www.circuitsathome.com e-mail : support@circuitsathome.com - */ +*/ /* Google ADK interface support header */ @@ -26,6 +26,10 @@ e-mail : support@circuitsathome.com #define ADK_PID 0x2D00 #define ADB_PID 0x2D01 +#define XOOM //enables repeating getProto() and getConf() attempts + //necessary for slow devices such as Motorola XOOM + //defined by default, can be commented out to save memory + /* requests */ #define ADK_GETPROTO 51 //check USB accessory protocol version diff --git a/examples/Bluetooth/PS3BT/PS3BT.ino b/examples/Bluetooth/PS3BT/PS3BT.ino index 3cb83213..f8b13ad7 100644 --- a/examples/Bluetooth/PS3BT/PS3BT.ino +++ b/examples/Bluetooth/PS3BT/PS3BT.ino @@ -1,6 +1,6 @@ /* Example sketch for the PS3 Bluetooth library - developed by Kristian Lauszus - For more information visit my blog: http://blog.tkjelectronics.dk/ or + For more information visit my blog: http://blog.tkjelectronics.dk/ or send me an e-mail: kristianl@tkjelectronics.com */ @@ -8,7 +8,8 @@ #include USB Usb; -USBHub Hub1(&Usb); // Some dongles have a hub inside +//USBHub Hub1(&Usb); // Some dongles have a hub inside + BTD Btd(&Usb); // You have to create the Bluetooth Dongle instance like so /* You can create the instance of the class in two ways */ PS3BT PS3(&Btd); // This will just create the instance @@ -22,152 +23,152 @@ void setup() { while (!Serial); // Wait for serial port to connect - used on Leonardo, Teensy and other boards with built-in USB CDC serial connection if (Usb.Init() == -1) { Serial.print(F("\r\nOSC did not start")); - while(1); //halt + while (1); //halt } Serial.print(F("\r\nPS3 Bluetooth Library Started")); } void loop() { Usb.Task(); - if(PS3.PS3Connected || PS3.PS3NavigationConnected) { - if(PS3.getAnalogHat(LeftHatX) > 137 || PS3.getAnalogHat(LeftHatX) < 117 || PS3.getAnalogHat(LeftHatY) > 137 || PS3.getAnalogHat(LeftHatY) < 117 || PS3.getAnalogHat(RightHatX) > 137 || PS3.getAnalogHat(RightHatX) < 117 || PS3.getAnalogHat(RightHatY) > 137 || PS3.getAnalogHat(RightHatY) < 117) { - Serial.print(F("\r\nLeftHatX: ")); + if (PS3.PS3Connected || PS3.PS3NavigationConnected) { + if (PS3.getAnalogHat(LeftHatX) > 137 || PS3.getAnalogHat(LeftHatX) < 117 || PS3.getAnalogHat(LeftHatY) > 137 || PS3.getAnalogHat(LeftHatY) < 117 || PS3.getAnalogHat(RightHatX) > 137 || PS3.getAnalogHat(RightHatX) < 117 || PS3.getAnalogHat(RightHatY) > 137 || PS3.getAnalogHat(RightHatY) < 117) { + Serial.print(F("\r\nLeftHatX: ")); Serial.print(PS3.getAnalogHat(LeftHatX)); - Serial.print(F("\tLeftHatY: ")); + Serial.print(F("\tLeftHatY: ")); Serial.print(PS3.getAnalogHat(LeftHatY)); - if(!PS3.PS3NavigationConnected) { - Serial.print(F("\tRightHatX: ")); + if (PS3.PS3Connected) { // The Navigation controller only have one joystick + Serial.print(F("\tRightHatX: ")); Serial.print(PS3.getAnalogHat(RightHatX)); - Serial.print(F("\tRightHatY: ")); + Serial.print(F("\tRightHatY: ")); Serial.print(PS3.getAnalogHat(RightHatY)); - } + } } - //Analog button values can be read from almost all buttons - if(PS3.getAnalogButton(L2) || PS3.getAnalogButton(R2)) { - Serial.print(F("\r\nL2: ")); + // Analog button values can be read from almost all buttons + if (PS3.getAnalogButton(L2) || PS3.getAnalogButton(R2)) { + Serial.print(F("\r\nL2: ")); Serial.print(PS3.getAnalogButton(L2)); - if(!PS3.PS3NavigationConnected) { - Serial.print(F("\tR2: ")); + if (!PS3.PS3NavigationConnected) { + Serial.print(F("\tR2: ")); Serial.print(PS3.getAnalogButton(R2)); } } - if(PS3.getButtonClick(PS)) { + if (PS3.getButtonClick(PS)) { Serial.print(F("\r\nPS")); PS3.disconnect(); - } + } else { - if(PS3.getButtonClick(TRIANGLE)) + if (PS3.getButtonClick(TRIANGLE)) Serial.print(F("\r\nTraingle")); - if(PS3.getButtonClick(CIRCLE)) + if (PS3.getButtonClick(CIRCLE)) Serial.print(F("\r\nCircle")); - if(PS3.getButtonClick(CROSS)) + if (PS3.getButtonClick(CROSS)) Serial.print(F("\r\nCross")); - if(PS3.getButtonClick(SQUARE)) + if (PS3.getButtonClick(SQUARE)) Serial.print(F("\r\nSquare")); - if(PS3.getButtonClick(UP)) { - Serial.print(F("\r\nUp")); - if(PS3.PS3Connected) { - PS3.setAllOff(); + if (PS3.getButtonClick(UP)) { + Serial.print(F("\r\nUp")); + if (PS3.PS3Connected) { + PS3.setLedOff(); PS3.setLedOn(LED4); } - } - if(PS3.getButtonClick(RIGHT)) { + } + if (PS3.getButtonClick(RIGHT)) { Serial.print(F("\r\nRight")); - if(PS3.PS3Connected) { - PS3.setAllOff(); - PS3.setLedOn(LED1); - } - } - if(PS3.getButtonClick(DOWN)) { - Serial.print(F("\r\nDown")); - if(PS3.PS3Connected) { - PS3.setAllOff(); - PS3.setLedOn(LED2); + if (PS3.PS3Connected) { + PS3.setLedOff(); + PS3.setLedOn(LED1); } - } - if(PS3.getButtonClick(LEFT)) { - Serial.print(F("\r\nLeft")); - if(PS3.PS3Connected) { - PS3.setAllOff(); - PS3.setLedOn(LED3); - } - } + } + if (PS3.getButtonClick(DOWN)) { + Serial.print(F("\r\nDown")); + if (PS3.PS3Connected) { + PS3.setLedOff(); + PS3.setLedOn(LED2); + } + } + if (PS3.getButtonClick(LEFT)) { + Serial.print(F("\r\nLeft")); + if (PS3.PS3Connected) { + PS3.setLedOff(); + PS3.setLedOn(LED3); + } + } - if(PS3.getButtonClick(L1)) - Serial.print(F("\r\nL1")); - if(PS3.getButtonClick(L3)) - Serial.print(F("\r\nL3")); - if(PS3.getButtonClick(R1)) - Serial.print(F("\r\nR1")); - if(PS3.getButtonClick(R3)) + if (PS3.getButtonClick(L1)) + Serial.print(F("\r\nL1")); + if (PS3.getButtonClick(L3)) + Serial.print(F("\r\nL3")); + if (PS3.getButtonClick(R1)) + Serial.print(F("\r\nR1")); + if (PS3.getButtonClick(R3)) Serial.print(F("\r\nR3")); - if(PS3.getButtonClick(SELECT)) { - Serial.print(F("\r\nSelect - ")); - Serial.print(PS3.getStatusString()); - } - if(PS3.getButtonClick(START)) { - Serial.print(F("\r\nStart")); + if (PS3.getButtonClick(SELECT)) { + Serial.print(F("\r\nSelect - ")); + Serial.print(PS3.getStatusString()); + } + if (PS3.getButtonClick(START)) { + Serial.print(F("\r\nStart")); printAngle = !printAngle; - } + } } - if(printAngle) { - Serial.print(F("\r\nPitch: ")); - Serial.print(PS3.getAngle(Pitch)); - Serial.print(F("\tRoll: ")); + if (printAngle) { + Serial.print(F("\r\nPitch: ")); + Serial.print(PS3.getAngle(Pitch)); + Serial.print(F("\tRoll: ")); Serial.print(PS3.getAngle(Roll)); } } - else if(PS3.PS3MoveConnected) { - if(PS3.getAnalogButton(T)) { - Serial.print(F("\r\nT: ")); - Serial.print(PS3.getAnalogButton(T)); - } - if(PS3.getButtonClick(PS)) { + else if (PS3.PS3MoveConnected) { + if (PS3.getAnalogButton(T)) { + Serial.print(F("\r\nT: ")); + Serial.print(PS3.getAnalogButton(T)); + } + if (PS3.getButtonClick(PS)) { Serial.print(F("\r\nPS")); PS3.disconnect(); - } + } else { - if(PS3.getButtonClick(SELECT)) { + if (PS3.getButtonClick(SELECT)) { Serial.print(F("\r\nSelect")); printTemperature = !printTemperature; - } - if(PS3.getButtonClick(START)) { + } + if (PS3.getButtonClick(START)) { Serial.print(F("\r\nStart")); - printAngle = !printAngle; - } - if(PS3.getButtonClick(TRIANGLE)) { + printAngle = !printAngle; + } + if (PS3.getButtonClick(TRIANGLE)) { Serial.print(F("\r\nTriangle")); PS3.moveSetBulb(Red); - } - if(PS3.getButtonClick(CIRCLE)) { + } + if (PS3.getButtonClick(CIRCLE)) { Serial.print(F("\r\nCircle")); PS3.moveSetBulb(Green); - } - if(PS3.getButtonClick(SQUARE)) { + } + if (PS3.getButtonClick(SQUARE)) { Serial.print(F("\r\nSquare")); PS3.moveSetBulb(Blue); - } - if(PS3.getButtonClick(CROSS)) { + } + if (PS3.getButtonClick(CROSS)) { Serial.print(F("\r\nCross")); PS3.moveSetBulb(Yellow); - } - if(PS3.getButtonClick(MOVE)) { - PS3.moveSetBulb(Off); + } + if (PS3.getButtonClick(MOVE)) { + PS3.moveSetBulb(Off); Serial.print(F("\r\nMove")); - Serial.print(F(" - ")); + Serial.print(F(" - ")); Serial.print(PS3.getStatusString()); } } - if(printAngle) { - Serial.print(F("\r\nPitch: ")); - Serial.print(PS3.getAngle(Pitch)); - Serial.print(F("\tRoll: ")); + if (printAngle) { + Serial.print(F("\r\nPitch: ")); + Serial.print(PS3.getAngle(Pitch)); + Serial.print(F("\tRoll: ")); Serial.print(PS3.getAngle(Roll)); } - else if(printTemperature) { + else if (printTemperature) { Serial.print(F("\r\nTemperature: ")); Serial.print(PS3.getTemperature()); } diff --git a/examples/Bluetooth/PS3Multi/PS3Multi.ino b/examples/Bluetooth/PS3Multi/PS3Multi.ino index d3f172b6..d7ec631c 100644 --- a/examples/Bluetooth/PS3Multi/PS3Multi.ino +++ b/examples/Bluetooth/PS3Multi/PS3Multi.ino @@ -1,7 +1,7 @@ /* Example sketch for the PS3 Bluetooth library - developed by Kristian Lauszus This example show how one can use multiple controllers with the library - For more information visit my blog: http://blog.tkjelectronics.dk/ or + For more information visit my blog: http://blog.tkjelectronics.dk/ or send me an e-mail: kristianl@tkjelectronics.com */ @@ -9,15 +9,16 @@ #include USB Usb; -USBHub Hub1(&Usb); // Some dongles have a hub inside +//USBHub Hub1(&Usb); // Some dongles have a hub inside + BTD Btd(&Usb); // You have to create the Bluetooth Dongle instance like so PS3BT *PS3[2]; // We will use this pointer to store the two instance, you can easily make it larger if you like, but it will use a lot of RAM! -const uint8_t length = sizeof(PS3)/sizeof(PS3[0]); // Get the lenght of the array +const uint8_t length = sizeof(PS3) / sizeof(PS3[0]); // Get the lenght of the array boolean printAngle[length]; boolean oldControllerState[length]; void setup() { - for (uint8_t i=0;iattachOnInit(onInit); // onInit() is called upon a new connection - you can call the function whatever you like } @@ -26,21 +27,21 @@ void setup() { while (!Serial); // Wait for serial port to connect - used on Leonardo, Teensy and other boards with built-in USB CDC serial connection if (Usb.Init() == -1) { Serial.print(F("\r\nOSC did not start")); - while(1); //halt + while (1); //halt } Serial.print(F("\r\nPS3 Bluetooth Library Started")); } void loop() { Usb.Task(); - for(uint8_t i=0;iPS3Connected || PS3[i]->PS3NavigationConnected) { - if(PS3[i]->getAnalogHat(LeftHatX) > 137 || PS3[i]->getAnalogHat(LeftHatX) < 117 || PS3[i]->getAnalogHat(LeftHatY) > 137 || PS3[i]->getAnalogHat(LeftHatY) < 117 || PS3[i]->getAnalogHat(RightHatX) > 137 || PS3[i]->getAnalogHat(RightHatX) < 117 || PS3[i]->getAnalogHat(RightHatY) > 137 || PS3[i]->getAnalogHat(RightHatY) < 117) { + for (uint8_t i = 0; i < length; i++) { + if (PS3[i]->PS3Connected || PS3[i]->PS3NavigationConnected) { + if (PS3[i]->getAnalogHat(LeftHatX) > 137 || PS3[i]->getAnalogHat(LeftHatX) < 117 || PS3[i]->getAnalogHat(LeftHatY) > 137 || PS3[i]->getAnalogHat(LeftHatY) < 117 || PS3[i]->getAnalogHat(RightHatX) > 137 || PS3[i]->getAnalogHat(RightHatX) < 117 || PS3[i]->getAnalogHat(RightHatY) > 137 || PS3[i]->getAnalogHat(RightHatY) < 117) { Serial.print(F("\r\nLeftHatX: ")); Serial.print(PS3[i]->getAnalogHat(LeftHatX)); Serial.print(F("\tLeftHatY: ")); Serial.print(PS3[i]->getAnalogHat(LeftHatY)); - if(!PS3[i]->PS3NavigationConnected) { // The Navigation controller only have one joystick + if (PS3[i]->PS3Connected) { // The Navigation controller only have one joystick Serial.print(F("\tRightHatX: ")); Serial.print(PS3[i]->getAnalogHat(RightHatX)); Serial.print(F("\tRightHatY: ")); @@ -48,77 +49,77 @@ void loop() { } } //Analog button values can be read from almost all buttons - if(PS3[i]->getAnalogButton(L2) || PS3[i]->getAnalogButton(R2)) { + if (PS3[i]->getAnalogButton(L2) || PS3[i]->getAnalogButton(R2)) { Serial.print(F("\r\nL2: ")); Serial.print(PS3[i]->getAnalogButton(L2)); - if(!PS3[i]->PS3NavigationConnected) { + if (!PS3[i]->PS3NavigationConnected) { Serial.print(F("\tR2: ")); Serial.print(PS3[i]->getAnalogButton(R2)); } } - if(PS3[i]->getButtonClick(PS)) { + if (PS3[i]->getButtonClick(PS)) { Serial.print(F("\r\nPS")); PS3[i]->disconnect(); oldControllerState[i] = false; // Reset value } else { - if(PS3[i]->getButtonClick(TRIANGLE)) + if (PS3[i]->getButtonClick(TRIANGLE)) Serial.print(F("\r\nTraingle")); - if(PS3[i]->getButtonClick(CIRCLE)) + if (PS3[i]->getButtonClick(CIRCLE)) Serial.print(F("\r\nCircle")); - if(PS3[i]->getButtonClick(CROSS)) + if (PS3[i]->getButtonClick(CROSS)) Serial.print(F("\r\nCross")); - if(PS3[i]->getButtonClick(SQUARE)) + if (PS3[i]->getButtonClick(SQUARE)) Serial.print(F("\r\nSquare")); - if(PS3[i]->getButtonClick(UP)) { + if (PS3[i]->getButtonClick(UP)) { Serial.print(F("\r\nUp")); - if(PS3[i]->PS3Connected) { - PS3[i]->setAllOff(); + if (PS3[i]->PS3Connected) { + PS3[i]->setLedOff(); PS3[i]->setLedOn(LED4); } } - if(PS3[i]->getButtonClick(RIGHT)) { + if (PS3[i]->getButtonClick(RIGHT)) { Serial.print(F("\r\nRight")); - if(PS3[i]->PS3Connected) { - PS3[i]->setAllOff(); + if (PS3[i]->PS3Connected) { + PS3[i]->setLedOff(); PS3[i]->setLedOn(LED1); } } - if(PS3[i]->getButtonClick(DOWN)) { + if (PS3[i]->getButtonClick(DOWN)) { Serial.print(F("\r\nDown")); - if(PS3[i]->PS3Connected) { - PS3[i]->setAllOff(); + if (PS3[i]->PS3Connected) { + PS3[i]->setLedOff(); PS3[i]->setLedOn(LED2); } } - if(PS3[i]->getButtonClick(LEFT)) { + if (PS3[i]->getButtonClick(LEFT)) { Serial.print(F("\r\nLeft")); - if(PS3[i]->PS3Connected) { - PS3[i]->setAllOff(); + if (PS3[i]->PS3Connected) { + PS3[i]->setLedOff(); PS3[i]->setLedOn(LED3); } } - if(PS3[i]->getButtonClick(L1)) + if (PS3[i]->getButtonClick(L1)) Serial.print(F("\r\nL1")); - if(PS3[i]->getButtonClick(L3)) + if (PS3[i]->getButtonClick(L3)) Serial.print(F("\r\nL3")); - if(PS3[i]->getButtonClick(R1)) + if (PS3[i]->getButtonClick(R1)) Serial.print(F("\r\nR1")); - if(PS3[i]->getButtonClick(R3)) + if (PS3[i]->getButtonClick(R3)) Serial.print(F("\r\nR3")); - if(PS3[i]->getButtonClick(SELECT)) { + if (PS3[i]->getButtonClick(SELECT)) { Serial.print(F("\r\nSelect - ")); Serial.print(PS3[i]->getStatusString()); } - if(PS3[i]->getButtonClick(START)) { + if (PS3[i]->getButtonClick(START)) { Serial.print(F("\r\nStart")); printAngle[i] = !printAngle[i]; } } - if(printAngle[i]) { + if (printAngle[i]) { Serial.print(F("\r\nPitch: ")); Serial.print(PS3[i]->getAngle(Pitch)); Serial.print(F("\tRoll: ")); @@ -126,12 +127,12 @@ void loop() { } } /* I have removed the PS3 Move code as an Uno will run out of RAM if it's included */ - //else if(PS3[i]->PS3MoveConnected) { + //else if(PS3[i]->PS3MoveConnected) { } } void onInit() { - for (uint8_t i=0;iPS3Connected || PS3[i]->PS3NavigationConnected) && !oldControllerState[i]) { oldControllerState[i] = true; // Used to check which is the new controller PS3[i]->setLedOn((LED)i); // Cast directly to LED enum - see: "controllerEnums.h" diff --git a/examples/Bluetooth/PS3SPP/PS3SPP.ino b/examples/Bluetooth/PS3SPP/PS3SPP.ino index 8f8e751d..214ce26a 100644 --- a/examples/Bluetooth/PS3SPP/PS3SPP.ino +++ b/examples/Bluetooth/PS3SPP/PS3SPP.ino @@ -1,6 +1,6 @@ /* Example sketch for the Bluetooth library - developed by Kristian Lauszus - For more information visit my blog: http://blog.tkjelectronics.dk/ or + For more information visit my blog: http://blog.tkjelectronics.dk/ or send me an e-mail: kristianl@tkjelectronics.com This example show how one can combine all the difference Bluetooth services in one single code. @@ -14,7 +14,8 @@ #include USB Usb; -USBHub Hub1(&Usb); // Some dongles have a hub inside +//USBHub Hub1(&Usb); // Some dongles have a hub inside + BTD Btd(&Usb); // You have to create the Bluetooth Dongle instance like so /* You can create the instances of the bluetooth services in two ways */ @@ -31,7 +32,7 @@ void setup() { while (!Serial); // Wait for serial port to connect - used on Leonardo, Teensy and other boards with built-in USB CDC serial connection if (Usb.Init() == -1) { Serial.print(F("\r\nOSC did not start")); - while(1); //halt + while (1); //halt } Serial.print(F("\r\nBluetooth Library Started")); output.reserve(200); // Reserve 200 bytes for the output string @@ -39,27 +40,27 @@ void setup() { void loop() { Usb.Task(); // The SPP data is actually not send until this is called, one could call SerialBT.send() directly as well - if(SerialBT.connected) { - if(firstMessage) { + if (SerialBT.connected) { + if (firstMessage) { firstMessage = false; SerialBT.println(F("Hello from Arduino")); // Send welcome message } - if(Serial.available()) + if (Serial.available()) SerialBT.write(Serial.read()); - if(SerialBT.available()) + if (SerialBT.available()) Serial.write(SerialBT.read()); - } - else + } + else firstMessage = true; - if(PS3.PS3Connected || PS3.PS3NavigationConnected) { + if (PS3.PS3Connected || PS3.PS3NavigationConnected) { output = ""; // Reset output string - if(PS3.getAnalogHat(LeftHatX) > 137 || PS3.getAnalogHat(LeftHatX) < 117 || PS3.getAnalogHat(LeftHatY) > 137 || PS3.getAnalogHat(LeftHatY) < 117 || PS3.getAnalogHat(RightHatX) > 137 || PS3.getAnalogHat(RightHatX) < 117 || PS3.getAnalogHat(RightHatY) > 137 || PS3.getAnalogHat(RightHatY) < 117) { + if (PS3.getAnalogHat(LeftHatX) > 137 || PS3.getAnalogHat(LeftHatX) < 117 || PS3.getAnalogHat(LeftHatY) > 137 || PS3.getAnalogHat(LeftHatY) < 117 || PS3.getAnalogHat(RightHatX) > 137 || PS3.getAnalogHat(RightHatX) < 117 || PS3.getAnalogHat(RightHatY) > 137 || PS3.getAnalogHat(RightHatY) < 117) { output += "LeftHatX: "; output += PS3.getAnalogHat(LeftHatX); output += "\tLeftHatY: "; output += PS3.getAnalogHat(LeftHatY); - if(!PS3.PS3NavigationConnected) { + if (PS3.PS3Connected) { // The Navigation controller only have one joystick output += "\tRightHatX: "; output += PS3.getAnalogHat(RightHatX); output += "\tRightHatY: "; @@ -67,85 +68,85 @@ void loop() { } } //Analog button values can be read from almost all buttons - if(PS3.getAnalogButton(L2) || PS3.getAnalogButton(R2)) { - if(output != "") + if (PS3.getAnalogButton(L2) || PS3.getAnalogButton(R2)) { + if (output != "") output += "\r\n"; output += "L2: "; output += PS3.getAnalogButton(L2); - if(!PS3.PS3NavigationConnected) { + if (!PS3.PS3NavigationConnected) { output += "\tR2: "; output += PS3.getAnalogButton(R2); - } + } } - if(output != "") { + if (output != "") { Serial.println(output); - if(SerialBT.connected) + if (SerialBT.connected) SerialBT.println(output); output = ""; // Reset output string } - if(PS3.getButtonClick(PS)) { + if (PS3.getButtonClick(PS)) { output += " - PS"; PS3.disconnect(); - } + } else { - if(PS3.getButtonClick(TRIANGLE)) + if (PS3.getButtonClick(TRIANGLE)) output += " - Traingle"; - if(PS3.getButtonClick(CIRCLE)) + if (PS3.getButtonClick(CIRCLE)) output += " - Circle"; - if(PS3.getButtonClick(CROSS)) + if (PS3.getButtonClick(CROSS)) output += " - Cross"; - if(PS3.getButtonClick(SQUARE)) + if (PS3.getButtonClick(SQUARE)) output += " - Square"; - if(PS3.getButtonClick(UP)) { + if (PS3.getButtonClick(UP)) { output += " - Up"; - if(PS3.PS3Connected) { - PS3.setAllOff(); + if (PS3.PS3Connected) { + PS3.setLedOff(); PS3.setLedOn(LED4); } - } - if(PS3.getButtonClick(RIGHT)) { + } + if (PS3.getButtonClick(RIGHT)) { output += " - Right"; - if(PS3.PS3Connected) { - PS3.setAllOff(); - PS3.setLedOn(LED1); - } - } - if(PS3.getButtonClick(DOWN)) { - output += " - Down"; - if(PS3.PS3Connected) { - PS3.setAllOff(); - PS3.setLedOn(LED2); + if (PS3.PS3Connected) { + PS3.setLedOff(); + PS3.setLedOn(LED1); } - } - if(PS3.getButtonClick(LEFT)) { - output += " - Left"; - if(PS3.PS3Connected) { - PS3.setAllOff(); - PS3.setLedOn(LED3); - } - } + } + if (PS3.getButtonClick(DOWN)) { + output += " - Down"; + if (PS3.PS3Connected) { + PS3.setLedOff(); + PS3.setLedOn(LED2); + } + } + if (PS3.getButtonClick(LEFT)) { + output += " - Left"; + if (PS3.PS3Connected) { + PS3.setLedOff(); + PS3.setLedOn(LED3); + } + } - if(PS3.getButtonClick(L1)) + if (PS3.getButtonClick(L1)) output += " - L1"; - if(PS3.getButtonClick(L3)) - output += " - L3"; - if(PS3.getButtonClick(R1)) - output += " - R1"; - if(PS3.getButtonClick(R3)) - output += " - R3"; + if (PS3.getButtonClick(L3)) + output += " - L3"; + if (PS3.getButtonClick(R1)) + output += " - R1"; + if (PS3.getButtonClick(R3)) + output += " - R3"; - if(PS3.getButtonClick(SELECT)) { + if (PS3.getButtonClick(SELECT)) { output += " - Select - "; output += PS3.getStatusString(); } - if(PS3.getButtonClick(START)) - output += " - Start"; + if (PS3.getButtonClick(START)) + output += " - Start"; - if(output != "") { + if (output != "") { String string = "PS3 Controller" + output; Serial.println(string); - if(SerialBT.connected) + if (SerialBT.connected) SerialBT.println(string); } } diff --git a/examples/Bluetooth/SPP/SPP.ino b/examples/Bluetooth/SPP/SPP.ino index eb91459c..e5b92089 100644 --- a/examples/Bluetooth/SPP/SPP.ino +++ b/examples/Bluetooth/SPP/SPP.ino @@ -1,6 +1,6 @@ /* Example sketch for the RFCOMM/SPP Bluetooth library - developed by Kristian Lauszus - For more information visit my blog: http://blog.tkjelectronics.dk/ or + For more information visit my blog: http://blog.tkjelectronics.dk/ or send me an e-mail: kristianl@tkjelectronics.com */ @@ -8,7 +8,8 @@ #include USB Usb; -USBHub Hub1(&Usb); // Some dongles have a hub inside +//USBHub Hub1(&Usb); // Some dongles have a hub inside + BTD Btd(&Usb); // You have to create the Bluetooth Dongle instance like so /* You can create the instance of the class in two ways */ SPP SerialBT(&Btd); // This will set the name to the defaults: "Arduino" and the pin to "1234" @@ -21,23 +22,23 @@ void setup() { while (!Serial); // Wait for serial port to connect - used on Leonardo, Teensy and other boards with built-in USB CDC serial connection if (Usb.Init() == -1) { Serial.print(F("\r\nOSC did not start")); - while(1); //halt + while (1); //halt } Serial.print(F("\r\nSPP Bluetooth Library Started")); } void loop() { Usb.Task(); // The SPP data is actually not send until this is called, one could call SerialBT.send() directly as well - - if(SerialBT.connected) { - if(firstMessage) { + + if (SerialBT.connected) { + if (firstMessage) { firstMessage = false; SerialBT.println(F("Hello from Arduino")); // Send welcome message } - if(Serial.available()) + if (Serial.available()) SerialBT.write(Serial.read()); - if(SerialBT.available()) + if (SerialBT.available()) Serial.write(SerialBT.read()); - } - else + } + else firstMessage = true; } diff --git a/examples/Bluetooth/SPPMulti/SPPMulti.ino b/examples/Bluetooth/SPPMulti/SPPMulti.ino index 483bdfbd..af32fd85 100644 --- a/examples/Bluetooth/SPPMulti/SPPMulti.ino +++ b/examples/Bluetooth/SPPMulti/SPPMulti.ino @@ -1,6 +1,6 @@ /* Example sketch for the RFCOMM/SPP Bluetooth library - developed by Kristian Lauszus - For more information visit my blog: http://blog.tkjelectronics.dk/ or + For more information visit my blog: http://blog.tkjelectronics.dk/ or send me an e-mail: kristianl@tkjelectronics.com */ @@ -8,56 +8,57 @@ #include USB Usb; -USBHub Hub1(&Usb); // Some dongles have a hub inside +//USBHub Hub1(&Usb); // Some dongles have a hub inside + BTD Btd(&Usb); // You have to create the Bluetooth Dongle instance like so -SPP* SerialBT[2]; // We will use this pointer to store the two instance, you can easily make it larger if you like, but it will use a lot of RAM! -const uint8_t length = sizeof(SerialBT)/sizeof(SerialBT[0]); // Get the lenght of the array +SPP *SerialBT[2]; // We will use this pointer to store the two instance, you can easily make it larger if you like, but it will use a lot of RAM! +const uint8_t length = sizeof(SerialBT) / sizeof(SerialBT[0]); // Get the lenght of the array boolean firstMessage[length] = { true }; // Set all to true uint8_t buffer[50]; void setup() { - for(uint8_t i=0;iconnected) { - if(firstMessage[i]) { + + for (uint8_t i = 0; i < length; i++) { + if (SerialBT[i]->connected) { + if (firstMessage[i]) { firstMessage[i] = false; SerialBT[i]->println(F("Hello from Arduino")); // Send welcome message } - if(SerialBT[i]->available()) + if (SerialBT[i]->available()) Serial.write(SerialBT[i]->read()); - } + } else firstMessage[i] = true; } - if(Serial.available()) { + if (Serial.available()) { delay(10); // Wait for the rest of the data to arrive uint8_t i = 0; - while(Serial.available() && i < sizeof(buffer)) // Read the data + while (Serial.available() && i < sizeof(buffer)) // Read the data buffer[i++] = Serial.read(); - /* + /* Set the connection you want to send to using the first character - For instace "0Hello World" would send "Hello World" to connection 0 + For instace "0Hello World" would send "Hello World" to connection 0 */ - uint8_t id = buffer[0]-'0'; // Convert from ASCII - if(id < length && i > 1) { // And then compare to length and make sure there is any text - if(SerialBT[id]->connected) { // Check if a device is actually connected - for(uint8_t i2 = 0; i2 < i-1; i2++) // Don't include the first character - buffer[i2] = buffer[i2+1]; - SerialBT[id]->write(buffer,i-1); // Send the data + uint8_t id = buffer[0] - '0'; // Convert from ASCII + if (id < length && i > 1) { // And then compare to length and make sure there is any text + if (SerialBT[id]->connected) { // Check if a device is actually connected + for (uint8_t i2 = 0; i2 < i - 1; i2++) // Don't include the first character + buffer[i2] = buffer[i2 + 1]; + SerialBT[id]->write(buffer, i - 1); // Send the data } } - } + } } diff --git a/examples/Bluetooth/Wii/Wii.ino b/examples/Bluetooth/Wii/Wii.ino index 815c16fe..214625c5 100644 --- a/examples/Bluetooth/Wii/Wii.ino +++ b/examples/Bluetooth/Wii/Wii.ino @@ -1,6 +1,6 @@ /* Example sketch for the Wiimote Bluetooth library - developed by Kristian Lauszus - For more information visit my blog: http://blog.tkjelectronics.dk/ or + For more information visit my blog: http://blog.tkjelectronics.dk/ or send me an e-mail: kristianl@tkjelectronics.com */ @@ -8,10 +8,11 @@ #include USB Usb; -USBHub Hub1(&Usb); // Some dongles have a hub inside +//USBHub Hub1(&Usb); // Some dongles have a hub inside + BTD Btd(&Usb); // You have to create the Bluetooth Dongle instance like so /* You can create the instance of the class in two ways */ -WII Wii(&Btd,PAIR); // This will start an inquiry and then pair with your Wiimote - you only have to do this once +WII Wii(&Btd, PAIR); // This will start an inquiry and then pair with your Wiimote - you only have to do this once //WII Wii(&Btd); // After that you can simply create the instance like so and then press any button on the Wiimote bool printAngle; @@ -21,68 +22,68 @@ void setup() { while (!Serial); // Wait for serial port to connect - used on Leonardo, Teensy and other boards with built-in USB CDC serial connection if (Usb.Init() == -1) { Serial.print(F("\r\nOSC did not start")); - while(1); //halt + while (1); //halt } Serial.print(F("\r\nWiimote Bluetooth Library Started")); } void loop() { Usb.Task(); - if(Wii.wiimoteConnected) { - if(Wii.getButtonClick(HOME)) { // You can use getButtonPress to see if the button is held down + if (Wii.wiimoteConnected) { + if (Wii.getButtonClick(HOME)) { // You can use getButtonPress to see if the button is held down Serial.print(F("\r\nHOME")); Wii.disconnect(); - } + } else { - if(Wii.getButtonClick(LEFT)) { - Wii.setAllOff(); + if (Wii.getButtonClick(LEFT)) { + Wii.setLedOff(); Wii.setLedOn(LED1); Serial.print(F("\r\nLeft")); } - if(Wii.getButtonClick(RIGHT)) { - Wii.setAllOff(); + if (Wii.getButtonClick(RIGHT)) { + Wii.setLedOff(); Wii.setLedOn(LED3); Serial.print(F("\r\nRight")); } - if(Wii.getButtonClick(DOWN)) { - Wii.setAllOff(); + if (Wii.getButtonClick(DOWN)) { + Wii.setLedOff(); Wii.setLedOn(LED4); Serial.print(F("\r\nDown")); - } - if(Wii.getButtonClick(UP)) { - Wii.setAllOff(); - Wii.setLedOn(LED2); + } + if (Wii.getButtonClick(UP)) { + Wii.setLedOff(); + Wii.setLedOn(LED2); Serial.print(F("\r\nUp")); } - if(Wii.getButtonClick(PLUS)) + if (Wii.getButtonClick(PLUS)) Serial.print(F("\r\nPlus")); - if(Wii.getButtonClick(MINUS)) + if (Wii.getButtonClick(MINUS)) Serial.print(F("\r\nMinus")); - if(Wii.getButtonClick(ONE)) + if (Wii.getButtonClick(ONE)) Serial.print(F("\r\nOne")); - if(Wii.getButtonClick(TWO)) + if (Wii.getButtonClick(TWO)) Serial.print(F("\r\nTwo")); - if(Wii.getButtonClick(A)) { + if (Wii.getButtonClick(A)) { printAngle = !printAngle; Serial.print(F("\r\nA")); - } - if(Wii.getButtonClick(B)) { + } + if (Wii.getButtonClick(B)) { Wii.setRumbleToggle(); Serial.print(F("\r\nB")); } } - if(printAngle) { + if (printAngle) { Serial.print(F("\r\nPitch: ")); Serial.print(Wii.getPitch()); Serial.print(F("\tRoll: ")); Serial.print(Wii.getRoll()); - if(Wii.motionPlusConnected) { + if (Wii.motionPlusConnected) { Serial.print(F("\tYaw: ")); Serial.print(Wii.getYaw()); - } - if(Wii.nunchuckConnected) { + } + if (Wii.nunchuckConnected) { Serial.print(F("\tNunchuck Pitch: ")); Serial.print(Wii.getNunchuckPitch()); Serial.print(F("\tNunchuck Roll: ")); @@ -90,12 +91,12 @@ void loop() { } } } - if(Wii.nunchuckConnected) { - if(Wii.getButtonClick(Z)) + if (Wii.nunchuckConnected) { + if (Wii.getButtonClick(Z)) Serial.print(F("\r\nZ")); - if(Wii.getButtonClick(C)) + if (Wii.getButtonClick(C)) Serial.print(F("\r\nC")); - if(Wii.getAnalogHat(HatX) > 137 || Wii.getAnalogHat(HatX) < 117 || Wii.getAnalogHat(HatY) > 137 || Wii.getAnalogHat(HatY) < 117) { + if (Wii.getAnalogHat(HatX) > 137 || Wii.getAnalogHat(HatX) < 117 || Wii.getAnalogHat(HatY) > 137 || Wii.getAnalogHat(HatY) < 117) { Serial.print(F("\r\nHatX: ")); Serial.print(Wii.getAnalogHat(HatX)); Serial.print(F("\tHatY: ")); diff --git a/examples/Bluetooth/WiiIRCamera/WiiIRCamera.ino b/examples/Bluetooth/WiiIRCamera/WiiIRCamera.ino index 08aed4e0..5d0fa91b 100644 --- a/examples/Bluetooth/WiiIRCamera/WiiIRCamera.ino +++ b/examples/Bluetooth/WiiIRCamera/WiiIRCamera.ino @@ -1,12 +1,12 @@ /* Example sketch for the Wii libary showing the IR camera functionality. This example is for the Bluetooth Wii library developed for the USB shield from Circuits@Home - + Created by Allan Glover and Kristian Lauszus. Contact Kristian: http://blog.tkjelectronics.dk/ or send an email at kristianl@tkjelectronics.com. Contact Allan at adglover9.81@gmail.com - -To test the Wiimote IR camera, you will need access to an IR source. Sunlight will work but is not ideal. + +To test the Wiimote IR camera, you will need access to an IR source. Sunlight will work but is not ideal. The simpleist solution is to use the Wii sensor bar, i.e. emitter bar, supplied by the Wii system. Otherwise, wire up a IR LED yourself. */ @@ -19,10 +19,11 @@ Otherwise, wire up a IR LED yourself. #endif USB Usb; -USBHub Hub1(&Usb); // Some dongles have a hub inside +//USBHub Hub1(&Usb); // Some dongles have a hub inside + BTD Btd(&Usb); // You have to create the Bluetooth Dongle instance like so /* You can create the instance of the class in two ways */ -WII Wii(&Btd,PAIR); // This will start an inquiry and then pair with your Wiimote - you only have to do this once +WII Wii(&Btd, PAIR); // This will start an inquiry and then pair with your Wiimote - you only have to do this once //WII Wii(&Btd); // After the Wiimote pairs once with the line of code above, you can simply create the instance like so and re upload and then press any button on the Wiimote bool printAngle; @@ -33,31 +34,31 @@ void setup() { while (!Serial); // Wait for serial port to connect - used on Leonardo, Teensy and other boards with built-in USB CDC serial connection if (Usb.Init() == -1) { Serial.print(F("\r\nOSC did not start")); - while(1); //halt + while (1); //halt } Serial.print(F("\r\nWiimote Bluetooth Library Started")); } void loop() { Usb.Task(); - if(Wii.wiimoteConnected) { - if(Wii.getButtonClick(HOME)) { // You can use getButtonPress to see if the button is held down + if (Wii.wiimoteConnected) { + if (Wii.getButtonClick(HOME)) { // You can use getButtonPress to see if the button is held down Serial.print(F("\r\nHOME")); Wii.disconnect(); } else { - if(Wii.getButtonClick(ONE)) + if (Wii.getButtonClick(ONE)) Wii.IRinitialize(); // Run the initialisation sequence - if(Wii.getButtonClick(MINUS) || Wii.getButtonClick(PLUS)) { - if(!Wii.isIRCameraEnabled()) + if (Wii.getButtonClick(MINUS) || Wii.getButtonClick(PLUS)) { + if (!Wii.isIRCameraEnabled()) Serial.print(F("\r\nEnable IR camera first")); else { - if(Wii.getButtonPress(MINUS)) { // getButtonClick will only return true once - if(printObjects > 0) - printObjects--; + if (Wii.getButtonPress(MINUS)) { // getButtonClick will only return true once + if (printObjects > 0) + printObjects--; } else { - if(printObjects < 4) + if (printObjects < 4) printObjects++; } Serial.print(F("\r\nTracking ")); @@ -65,56 +66,56 @@ void loop() { Serial.print(F(" objects")); } } - if(Wii.getButtonClick(A)) { + if (Wii.getButtonClick(A)) { printAngle = !printAngle; Serial.print(F("\r\nA")); } - if(Wii.getButtonClick(B)) { + if (Wii.getButtonClick(B)) { Serial.print(F("\r\nBattery level: ")); Serial.print(Wii.getBatteryLevel()); // You can get the battery level as well } } - if(printObjects > 0) { - if(Wii.getIRx1() != 0x3FF || Wii.getIRy1() != 0x3FF || Wii.getIRs1() != 0) { // Only print if the IR camera is actually seeing something + if (printObjects > 0) { + if (Wii.getIRx1() != 0x3FF || Wii.getIRy1() != 0x3FF || Wii.getIRs1() != 0) { // Only print if the IR camera is actually seeing something Serial.print(F("\r\nx1: ")); - Serial.print(Wii.getIRx1()); + Serial.print(Wii.getIRx1()); Serial.print(F("\ty1: ")); - Serial.print(Wii.getIRy1()); + Serial.print(Wii.getIRy1()); Serial.print(F("\ts1:")); Serial.print(Wii.getIRs1()); } - if(printObjects > 1) { - if(Wii.getIRx2() != 0x3FF || Wii.getIRy2() != 0x3FF || Wii.getIRs2() != 0) { + if (printObjects > 1) { + if (Wii.getIRx2() != 0x3FF || Wii.getIRy2() != 0x3FF || Wii.getIRs2() != 0) { Serial.print(F("\r\nx2: ")); - Serial.print(Wii.getIRx2()); + Serial.print(Wii.getIRx2()); Serial.print(F("\ty2: ")); - Serial.print(Wii.getIRy2()); + Serial.print(Wii.getIRy2()); Serial.print(F("\ts2:")); Serial.print(Wii.getIRs2()); } - if(printObjects > 2) { - if(Wii.getIRx3() != 0x3FF || Wii.getIRy3() != 0x3FF || Wii.getIRs3() != 0) { + if (printObjects > 2) { + if (Wii.getIRx3() != 0x3FF || Wii.getIRy3() != 0x3FF || Wii.getIRs3() != 0) { Serial.print(F("\r\nx3: ")); - Serial.print(Wii.getIRx3()); + Serial.print(Wii.getIRx3()); Serial.print(F("\ty3: ")); - Serial.print(Wii.getIRy3()); + Serial.print(Wii.getIRy3()); Serial.print(F("\ts3:")); Serial.print(Wii.getIRs3()); } - if(printObjects > 3) { - if(Wii.getIRx4() != 0x3FF || Wii.getIRy4() != 0x3FF || Wii.getIRs4() != 0) { + if (printObjects > 3) { + if (Wii.getIRx4() != 0x3FF || Wii.getIRy4() != 0x3FF || Wii.getIRs4() != 0) { Serial.print(F("\r\nx4: ")); - Serial.print(Wii.getIRx4()); + Serial.print(Wii.getIRx4()); Serial.print(F("\ty4: ")); - Serial.print(Wii.getIRy4()); + Serial.print(Wii.getIRy4()); Serial.print(F("\ts4:")); Serial.print(Wii.getIRs4()); } } } } - } - if(printAngle) { // There is no extension bytes available, so the MotionPlus or Nunchuck can't be read + } + if (printAngle) { // There is no extension bytes available, so the MotionPlus or Nunchuck can't be read Serial.print(F("\r\nPitch: ")); Serial.print(Wii.getPitch()); Serial.print(F("\tRoll: ")); diff --git a/examples/Bluetooth/WiiMulti/WiiMulti.ino b/examples/Bluetooth/WiiMulti/WiiMulti.ino index 0eae4d9a..51c9160b 100644 --- a/examples/Bluetooth/WiiMulti/WiiMulti.ino +++ b/examples/Bluetooth/WiiMulti/WiiMulti.ino @@ -1,7 +1,7 @@ /* Example sketch for the Wiimote Bluetooth library - developed by Kristian Lauszus This example show how one can use multiple controllers with the library - For more information visit my blog: http://blog.tkjelectronics.dk/ or + For more information visit my blog: http://blog.tkjelectronics.dk/ or send me an e-mail: kristianl@tkjelectronics.com */ @@ -9,88 +9,89 @@ #include USB Usb; -USBHub Hub1(&Usb); // Some dongles have a hub inside +//USBHub Hub1(&Usb); // Some dongles have a hub inside + BTD Btd(&Usb); // You have to create the Bluetooth Dongle instance like so WII *Wii[2]; // We will use this pointer to store the two instance, you can easily make it larger if you like, but it will use a lot of RAM! -const uint8_t length = sizeof(Wii)/sizeof(Wii[0]); // Get the lenght of the array +const uint8_t length = sizeof(Wii) / sizeof(Wii[0]); // Get the lenght of the array boolean printAngle[length]; boolean oldControllerState[length]; void setup() { - for (uint8_t i=0;iattachOnInit(onInit); // onInit() is called upon a new connection - you can call the function whatever you like } - + Serial.begin(115200); while (!Serial); // Wait for serial port to connect - used on Leonardo, Teensy and other boards with built-in USB CDC serial connection if (Usb.Init() == -1) { Serial.print(F("\r\nOSC did not start")); - while(1); //halt + while (1); //halt } Serial.print(F("\r\nWiimote Bluetooth Library Started")); } void loop() { Usb.Task(); - for(uint8_t i=0;iwiimoteConnected) { - if(Wii[i]->getButtonClick(HOME)) { // You can use getButtonPress to see if the button is held down + for (uint8_t i = 0; i < length; i++) { + if (Wii[i]->wiimoteConnected) { + if (Wii[i]->getButtonClick(HOME)) { // You can use getButtonPress to see if the button is held down Serial.print(F("\r\nHOME")); Wii[i]->disconnect(); oldControllerState[i] = false; // Reset value - } + } else { - if(Wii[i]->getButtonClick(LEFT)) { - Wii[i]->setAllOff(); + if (Wii[i]->getButtonClick(LEFT)) { + Wii[i]->setLedOff(); Wii[i]->setLedOn(LED1); Serial.print(F("\r\nLeft")); } - if(Wii[i]->getButtonClick(RIGHT)) { - Wii[i]->setAllOff(); + if (Wii[i]->getButtonClick(RIGHT)) { + Wii[i]->setLedOff(); Wii[i]->setLedOn(LED3); Serial.print(F("\r\nRight")); } - if(Wii[i]->getButtonClick(DOWN)) { - Wii[i]->setAllOff(); + if (Wii[i]->getButtonClick(DOWN)) { + Wii[i]->setLedOff(); Wii[i]->setLedOn(LED4); Serial.print(F("\r\nDown")); - } - if(Wii[i]->getButtonClick(UP)) { - Wii[i]->setAllOff(); - Wii[i]->setLedOn(LED2); + } + if (Wii[i]->getButtonClick(UP)) { + Wii[i]->setLedOff(); + Wii[i]->setLedOn(LED2); Serial.print(F("\r\nUp")); } - if(Wii[i]->getButtonClick(PLUS)) + if (Wii[i]->getButtonClick(PLUS)) Serial.print(F("\r\nPlus")); - if(Wii[i]->getButtonClick(MINUS)) + if (Wii[i]->getButtonClick(MINUS)) Serial.print(F("\r\nMinus")); - if(Wii[i]->getButtonClick(ONE)) + if (Wii[i]->getButtonClick(ONE)) Serial.print(F("\r\nOne")); - if(Wii[i]->getButtonClick(TWO)) + if (Wii[i]->getButtonClick(TWO)) Serial.print(F("\r\nTwo")); - if(Wii[i]->getButtonClick(A)) { + if (Wii[i]->getButtonClick(A)) { printAngle[i] = !printAngle[i]; Serial.print(F("\r\nA")); - } - if(Wii[i]->getButtonClick(B)) { + } + if (Wii[i]->getButtonClick(B)) { Wii[i]->setRumbleToggle(); Serial.print(F("\r\nB")); } } - if(printAngle[i]) { + if (printAngle[i]) { Serial.print(F("\r\nPitch: ")); Serial.print(Wii[i]->getPitch()); Serial.print(F("\tRoll: ")); Serial.print(Wii[i]->getRoll()); - if(Wii[i]->motionPlusConnected) { + if (Wii[i]->motionPlusConnected) { Serial.print(F("\tYaw: ")); Serial.print(Wii[i]->getYaw()); - } - if(Wii[i]->nunchuckConnected) { + } + if (Wii[i]->nunchuckConnected) { Serial.print(F("\tNunchuck Pitch: ")); Serial.print(Wii[i]->getNunchuckPitch()); Serial.print(F("\tNunchuck Roll: ")); @@ -98,12 +99,12 @@ void loop() { } } } - if(Wii[i]->nunchuckConnected) { - if(Wii[i]->getButtonClick(Z)) + if (Wii[i]->nunchuckConnected) { + if (Wii[i]->getButtonClick(Z)) Serial.print(F("\r\nZ")); - if(Wii[i]->getButtonClick(C)) + if (Wii[i]->getButtonClick(C)) Serial.print(F("\r\nC")); - if(Wii[i]->getAnalogHat(HatX) > 137 || Wii[i]->getAnalogHat(HatX) < 117 || Wii[i]->getAnalogHat(HatY) > 137 || Wii[i]->getAnalogHat(HatY) < 117) { + if (Wii[i]->getAnalogHat(HatX) > 137 || Wii[i]->getAnalogHat(HatX) < 117 || Wii[i]->getAnalogHat(HatY) > 137 || Wii[i]->getAnalogHat(HatY) < 117) { Serial.print(F("\r\nHatX: ")); Serial.print(Wii[i]->getAnalogHat(HatX)); Serial.print(F("\tHatY: ")); @@ -114,7 +115,7 @@ void loop() { } void onInit() { - for (uint8_t i=0;iwiimoteConnected && !oldControllerState[i]) { oldControllerState[i] = true; // Used to check which is the new controller Wii[i]->setLedOn((LED)i); // Cast directly to LED enum - see: "controllerEnums.h" diff --git a/examples/Bluetooth/WiiUProController/WiiUProController.ino b/examples/Bluetooth/WiiUProController/WiiUProController.ino index 6ba5618b..eb686879 100644 --- a/examples/Bluetooth/WiiUProController/WiiUProController.ino +++ b/examples/Bluetooth/WiiUProController/WiiUProController.ino @@ -1,6 +1,6 @@ /* Example sketch for the Wiimote Bluetooth library - developed by Kristian Lauszus - For more information visit my blog: http://blog.tkjelectronics.dk/ or + For more information visit my blog: http://blog.tkjelectronics.dk/ or send me an e-mail: kristianl@tkjelectronics.com */ @@ -8,10 +8,11 @@ #include USB Usb; -USBHub Hub1(&Usb); // Some dongles have a hub inside +//USBHub Hub1(&Usb); // Some dongles have a hub inside + BTD Btd(&Usb); // You have to create the Bluetooth Dongle instance like so /* You can create the instance of the class in two ways */ -WII Wii(&Btd,PAIR); // This will start an inquiry and then pair with your Wiimote - you only have to do this once +WII Wii(&Btd, PAIR); // This will start an inquiry and then pair with your Wiimote - you only have to do this once //WII Wii(&Btd); // After that you can simply create the instance like so and then press any button on the Wiimote void setup() { @@ -19,69 +20,69 @@ void setup() { while (!Serial); // Wait for serial port to connect - used on Leonardo, Teensy and other boards with built-in USB CDC serial connection if (Usb.Init() == -1) { Serial.print(F("\r\nOSC did not start")); - while(1); //halt + while (1); //halt } Serial.print(F("\r\nWiimote Bluetooth Library Started")); } void loop() { Usb.Task(); - if(Wii.wiiUProControllerConnected) { - if(Wii.getButtonClick(HOME)) { // You can use getButtonPress to see if the button is held down + if (Wii.wiiUProControllerConnected) { + if (Wii.getButtonClick(HOME)) { // You can use getButtonPress to see if the button is held down Serial.print(F("\r\nHome")); Wii.disconnect(); - } + } else { - if(Wii.getButtonClick(LEFT)) { - Wii.setAllOff(); + if (Wii.getButtonClick(LEFT)) { + Wii.setLedOff(); Wii.setLedOn(LED1); Serial.print(F("\r\nLeft")); } - if(Wii.getButtonClick(RIGHT)) { - Wii.setAllOff(); + if (Wii.getButtonClick(RIGHT)) { + Wii.setLedOff(); Wii.setLedOn(LED3); Serial.print(F("\r\nRight")); } - if(Wii.getButtonClick(DOWN)) { - Wii.setAllOff(); + if (Wii.getButtonClick(DOWN)) { + Wii.setLedOff(); Wii.setLedOn(LED4); Serial.print(F("\r\nDown")); - } - if(Wii.getButtonClick(UP)) { - Wii.setAllOff(); - Wii.setLedOn(LED2); + } + if (Wii.getButtonClick(UP)) { + Wii.setLedOff(); + Wii.setLedOn(LED2); Serial.print(F("\r\nUp")); } - if(Wii.getButtonClick(PLUS)) + if (Wii.getButtonClick(PLUS)) Serial.print(F("\r\nPlus")); - if(Wii.getButtonClick(MINUS)) + if (Wii.getButtonClick(MINUS)) Serial.print(F("\r\nMinus")); - if(Wii.getButtonClick(A)) + if (Wii.getButtonClick(A)) Serial.print(F("\r\nA")); - if(Wii.getButtonClick(B)) { + if (Wii.getButtonClick(B)) { Wii.setRumbleToggle(); Serial.print(F("\r\nB")); } - if(Wii.getButtonClick(X)) + if (Wii.getButtonClick(X)) Serial.print(F("\r\nX")); - if(Wii.getButtonClick(Y)) + if (Wii.getButtonClick(Y)) Serial.print(F("\r\nY")); - - if(Wii.getButtonClick(L)) + + if (Wii.getButtonClick(L)) Serial.print(F("\r\nL")); - if(Wii.getButtonClick(R)) + if (Wii.getButtonClick(R)) Serial.print(F("\r\nR")); - if(Wii.getButtonClick(ZL)) + if (Wii.getButtonClick(ZL)) Serial.print(F("\r\nZL")); - if(Wii.getButtonClick(ZR)) + if (Wii.getButtonClick(ZR)) Serial.print(F("\r\nZR")); - if(Wii.getButtonClick(L3)) + if (Wii.getButtonClick(L3)) Serial.print(F("\r\nL3")); - if(Wii.getButtonClick(R3)) - Serial.print(F("\r\nR3")); + if (Wii.getButtonClick(R3)) + Serial.print(F("\r\nR3")); } - if(Wii.getAnalogHat(LeftHatX) > 2200 || Wii.getAnalogHat(LeftHatX) < 1800 || Wii.getAnalogHat(LeftHatY) > 2200 || Wii.getAnalogHat(LeftHatY) < 1800 || Wii.getAnalogHat(RightHatX) > 2200 || Wii.getAnalogHat(RightHatX) < 1800 || Wii.getAnalogHat(RightHatY) > 2200 || Wii.getAnalogHat(RightHatY) < 1800) { + if (Wii.getAnalogHat(LeftHatX) > 2200 || Wii.getAnalogHat(LeftHatX) < 1800 || Wii.getAnalogHat(LeftHatY) > 2200 || Wii.getAnalogHat(LeftHatY) < 1800 || Wii.getAnalogHat(RightHatX) > 2200 || Wii.getAnalogHat(RightHatX) < 1800 || Wii.getAnalogHat(RightHatY) > 2200 || Wii.getAnalogHat(RightHatY) < 1800) { Serial.print(F("\r\nLeftHatX: ")); Serial.print(Wii.getAnalogHat(LeftHatX)); Serial.print(F("\tLeftHatY: ")); diff --git a/examples/PS3USB/PS3USB.ino b/examples/PS3USB/PS3USB.ino index 2a627a93..b3e6e2c4 100644 --- a/examples/PS3USB/PS3USB.ino +++ b/examples/PS3USB/PS3USB.ino @@ -1,6 +1,6 @@ /* Example sketch for the PS3 USB library - developed by Kristian Lauszus - For more information visit my blog: http://blog.tkjelectronics.dk/ or + For more information visit my blog: http://blog.tkjelectronics.dk/ or send me an e-mail: kristianl@tkjelectronics.com */ @@ -19,142 +19,122 @@ void setup() { while (!Serial); // Wait for serial port to connect - used on Leonardo, Teensy and other boards with built-in USB CDC serial connection if (Usb.Init() == -1) { Serial.print(F("\r\nOSC did not start")); - while(1); //halt - } + while (1); //halt + } Serial.print(F("\r\nPS3 USB Library Started")); } void loop() { Usb.Task(); - if(PS3.PS3Connected || PS3.PS3NavigationConnected) { - if(PS3.getAnalogHat(LeftHatX) > 137 || PS3.getAnalogHat(LeftHatX) < 117 || PS3.getAnalogHat(LeftHatY) > 137 || PS3.getAnalogHat(LeftHatY) < 117 || PS3.getAnalogHat(RightHatX) > 137 || PS3.getAnalogHat(RightHatX) < 117 || PS3.getAnalogHat(RightHatY) > 137 || PS3.getAnalogHat(RightHatY) < 117) { - Serial.print(F("\r\nLeftHatX: ")); + if (PS3.PS3Connected || PS3.PS3NavigationConnected) { + if (PS3.getAnalogHat(LeftHatX) > 137 || PS3.getAnalogHat(LeftHatX) < 117 || PS3.getAnalogHat(LeftHatY) > 137 || PS3.getAnalogHat(LeftHatY) < 117 || PS3.getAnalogHat(RightHatX) > 137 || PS3.getAnalogHat(RightHatX) < 117 || PS3.getAnalogHat(RightHatY) > 137 || PS3.getAnalogHat(RightHatY) < 117) { + Serial.print(F("\r\nLeftHatX: ")); Serial.print(PS3.getAnalogHat(LeftHatX)); - Serial.print(F("\tLeftHatY: ")); + Serial.print(F("\tLeftHatY: ")); Serial.print(PS3.getAnalogHat(LeftHatY)); - if(!PS3.PS3NavigationConnected) { - Serial.print(F("\tRightHatX: ")); + if (PS3.PS3Connected) { // The Navigation controller only have one joystick + Serial.print(F("\tRightHatX: ")); Serial.print(PS3.getAnalogHat(RightHatX)); - Serial.print(F("\tRightHatY: ")); + Serial.print(F("\tRightHatY: ")); Serial.print(PS3.getAnalogHat(RightHatY)); - } + } } // Analog button values can be read from almost all buttons - if(PS3.getAnalogButton(L2) || PS3.getAnalogButton(R2)) { - Serial.print(F("\r\nL2: ")); + if (PS3.getAnalogButton(L2) || PS3.getAnalogButton(R2)) { + Serial.print(F("\r\nL2: ")); Serial.print(PS3.getAnalogButton(L2)); - if(!PS3.PS3NavigationConnected) { - Serial.print(F("\tR2: ")); + if (!PS3.PS3NavigationConnected) { + Serial.print(F("\tR2: ")); Serial.print(PS3.getAnalogButton(R2)); - } + } } - if(PS3.getButtonClick(PS)) + if (PS3.getButtonClick(PS)) Serial.print(F("\r\nPS")); - if(PS3.getButtonClick(TRIANGLE)) + if (PS3.getButtonClick(TRIANGLE)) Serial.print(F("\r\nTraingle")); - if(PS3.getButtonClick(CIRCLE)) + if (PS3.getButtonClick(CIRCLE)) Serial.print(F("\r\nCircle")); - if(PS3.getButtonClick(CROSS)) + if (PS3.getButtonClick(CROSS)) Serial.print(F("\r\nCross")); - if(PS3.getButtonClick(SQUARE)) + if (PS3.getButtonClick(SQUARE)) Serial.print(F("\r\nSquare")); - if(PS3.getButtonClick(UP)) { + if (PS3.getButtonClick(UP)) { Serial.print(F("\r\nUp")); - PS3.setAllOff(); + PS3.setLedOff(); PS3.setLedOn(LED4); - } - if(PS3.getButtonClick(RIGHT)) { + } + if (PS3.getButtonClick(RIGHT)) { Serial.print(F("\r\nRight")); - PS3.setAllOff(); - PS3.setLedOn(LED1); - } - if(PS3.getButtonClick(DOWN)) { + PS3.setLedOff(); + PS3.setLedOn(LED1); + } + if (PS3.getButtonClick(DOWN)) { Serial.print(F("\r\nDown")); - PS3.setAllOff(); - PS3.setLedOn(LED2); - } - if(PS3.getButtonClick(LEFT)) { + PS3.setLedOff(); + PS3.setLedOn(LED2); + } + if (PS3.getButtonClick(LEFT)) { Serial.print(F("\r\nLeft")); - PS3.setAllOff(); - PS3.setLedOn(LED3); - } + PS3.setLedOff(); + PS3.setLedOn(LED3); + } - if(PS3.getButtonClick(L1)) - Serial.print(F("\r\nL1")); - if(PS3.getButtonClick(L3)) - Serial.print(F("\r\nL3")); - if(PS3.getButtonClick(R1)) - Serial.print(F("\r\nR1")); - if(PS3.getButtonClick(R3)) + if (PS3.getButtonClick(L1)) + Serial.print(F("\r\nL1")); + if (PS3.getButtonClick(L3)) + Serial.print(F("\r\nL3")); + if (PS3.getButtonClick(R1)) + Serial.print(F("\r\nR1")); + if (PS3.getButtonClick(R3)) Serial.print(F("\r\nR3")); - if(PS3.getButtonClick(SELECT)) { - Serial.print(F("\r\nSelect - ")); - Serial.print(PS3.getStatusString()); - } - if(PS3.getButtonClick(START)) { - Serial.print(F("\r\nStart")); - printAngle = !printAngle; - } - } - if(printAngle) { - Serial.print(F("\r\nPitch: ")); - Serial.print(PS3.getAngle(Pitch)); - Serial.print(F("\tRoll: ")); - Serial.print(PS3.getAngle(Roll)); - } - else if(PS3.PS3MoveConnected) { // One can only set the color of the bulb, set the rumble, set and get the bluetooth address and calibrate the magnetometer via USB - switch(state) { - case 0: - PS3.moveSetRumble(0); - PS3.moveSetBulb(Off); - state = 1; - break; - - case 1: - PS3.moveSetRumble(75); - PS3.moveSetBulb(Red); - state = 2; - break; - - case 2: - PS3.moveSetRumble(125); - PS3.moveSetBulb(Green); - state = 3; - break; - - case 3: - PS3.moveSetRumble(150); - PS3.moveSetBulb(Blue); - state = 4; - break; - - case 4: - PS3.moveSetRumble(175); - PS3.moveSetBulb(Yellow); - state = 5; - break; - - case 5: - PS3.moveSetRumble(200); - PS3.moveSetBulb(Lightblue); - state = 6; - break; - - case 6: - PS3.moveSetRumble(225); - PS3.moveSetBulb(Purble); - state = 7; - break; - - case 7: - PS3.moveSetRumble(250); - PS3.moveSetBulb(White); - state = 0; - break; + if (PS3.getButtonClick(SELECT)) { + Serial.print(F("\r\nSelect - ")); + Serial.print(PS3.getStatusString()); } + if (PS3.getButtonClick(START)) { + Serial.print(F("\r\nStart")); + printAngle = !printAngle; + } + if (printAngle) { + Serial.print(F("\r\nPitch: ")); + Serial.print(PS3.getAngle(Pitch)); + Serial.print(F("\tRoll: ")); + Serial.print(PS3.getAngle(Roll)); + } + } + else if (PS3.PS3MoveConnected) { // One can only set the color of the bulb, set the rumble, set and get the bluetooth address and calibrate the magnetometer via USB + if (state == 0) { + PS3.moveSetRumble(0); + PS3.moveSetBulb(Off); + } else if (state == 1) { + PS3.moveSetRumble(75); + PS3.moveSetBulb(Red); + } else if (state == 2) { + PS3.moveSetRumble(125); + PS3.moveSetBulb(Green); + } else if (state == 3) { + PS3.moveSetRumble(150); + PS3.moveSetBulb(Blue); + } else if (state == 4) { + PS3.moveSetRumble(175); + PS3.moveSetBulb(Yellow); + } else if (state == 5) { + PS3.moveSetRumble(200); + PS3.moveSetBulb(Lightblue); + } else if (state == 6) { + PS3.moveSetRumble(225); + PS3.moveSetBulb(Purble); + } else if (state == 7) { + PS3.moveSetRumble(250); + PS3.moveSetBulb(White); + } + + state++; + if (state > 7) + state = 0; delay(1000); } } diff --git a/examples/Xbox/XBOXOLD/XBOXOLD.ino b/examples/Xbox/XBOXOLD/XBOXOLD.ino index 22675172..1bdfc9f9 100644 --- a/examples/Xbox/XBOXOLD/XBOXOLD.ino +++ b/examples/Xbox/XBOXOLD/XBOXOLD.ino @@ -1,6 +1,6 @@ /* Example sketch for the original Xbox library - developed by Kristian Lauszus - For more information visit my blog: http://blog.tkjelectronics.dk/ or + For more information visit my blog: http://blog.tkjelectronics.dk/ or send me an e-mail: kristianl@tkjelectronics.com */ @@ -16,83 +16,84 @@ void setup() { while (!Serial); // Wait for serial port to connect - used on Leonardo, Teensy and other boards with built-in USB CDC serial connection if (Usb.Init() == -1) { Serial.print(F("\r\nOSC did not start")); - while(1); // halt - } + while (1); // halt + } Serial.print(F("\r\nXBOX Library Started")); } void loop() { Usb.Task(); - if(Xbox.XboxConnected) { - if(Xbox.getButtonPress(BLACK) || Xbox.getButtonPress(WHITE)) { + if (Xbox.XboxConnected) { + if (Xbox.getButtonPress(BLACK) || Xbox.getButtonPress(WHITE)) { Serial.print("BLACK: "); Serial.print(Xbox.getButtonPress(BLACK)); Serial.print("\tWHITE: "); Serial.println(Xbox.getButtonPress(WHITE)); - Xbox.setRumbleOn(Xbox.getButtonPress(BLACK),Xbox.getButtonPress(WHITE)); + Xbox.setRumbleOn(Xbox.getButtonPress(BLACK), Xbox.getButtonPress(WHITE)); } else - Xbox.setRumbleOn(0,0); - if(Xbox.getAnalogHat(LeftHatX) > 7500 || Xbox.getAnalogHat(LeftHatX) < -7500 || Xbox.getAnalogHat(LeftHatY) > 7500 || Xbox.getAnalogHat(LeftHatY) < -7500 || Xbox.getAnalogHat(RightHatX) > 7500 || Xbox.getAnalogHat(RightHatX) < -7500 || Xbox.getAnalogHat(RightHatY) > 7500 || Xbox.getAnalogHat(RightHatY) < -7500) { - if(Xbox.getAnalogHat(LeftHatX) > 7500 || Xbox.getAnalogHat(LeftHatX) < -7500) { - Serial.print(F("LeftHatX: ")); + Xbox.setRumbleOn(0, 0); + + if (Xbox.getAnalogHat(LeftHatX) > 7500 || Xbox.getAnalogHat(LeftHatX) < -7500 || Xbox.getAnalogHat(LeftHatY) > 7500 || Xbox.getAnalogHat(LeftHatY) < -7500 || Xbox.getAnalogHat(RightHatX) > 7500 || Xbox.getAnalogHat(RightHatX) < -7500 || Xbox.getAnalogHat(RightHatY) > 7500 || Xbox.getAnalogHat(RightHatY) < -7500) { + if (Xbox.getAnalogHat(LeftHatX) > 7500 || Xbox.getAnalogHat(LeftHatX) < -7500) { + Serial.print(F("LeftHatX: ")); Serial.print(Xbox.getAnalogHat(LeftHatX)); Serial.print("\t"); - } - if(Xbox.getAnalogHat(LeftHatY) > 7500 || Xbox.getAnalogHat(LeftHatY) < -7500) { - Serial.print(F("LeftHatY: ")); + } + if (Xbox.getAnalogHat(LeftHatY) > 7500 || Xbox.getAnalogHat(LeftHatY) < -7500) { + Serial.print(F("LeftHatY: ")); Serial.print(Xbox.getAnalogHat(LeftHatY)); Serial.print("\t"); - } - if(Xbox.getAnalogHat(RightHatX) > 7500 || Xbox.getAnalogHat(RightHatX) < -7500) { - Serial.print(F("RightHatX: ")); + } + if (Xbox.getAnalogHat(RightHatX) > 7500 || Xbox.getAnalogHat(RightHatX) < -7500) { + Serial.print(F("RightHatX: ")); Serial.print(Xbox.getAnalogHat(RightHatX)); - Serial.print("\t"); - } - if(Xbox.getAnalogHat(RightHatY) > 7500 || Xbox.getAnalogHat(RightHatY) < -7500) { - Serial.print(F("RightHatY: ")); - Serial.print(Xbox.getAnalogHat(RightHatY)); + Serial.print("\t"); + } + if (Xbox.getAnalogHat(RightHatY) > 7500 || Xbox.getAnalogHat(RightHatY) < -7500) { + Serial.print(F("RightHatY: ")); + Serial.print(Xbox.getAnalogHat(RightHatY)); } Serial.println(); } - - if(Xbox.getButtonClick(UP)) + + if (Xbox.getButtonClick(UP)) Serial.println(F("Up")); - if(Xbox.getButtonClick(DOWN)) + if (Xbox.getButtonClick(DOWN)) Serial.println(F("Down")); - if(Xbox.getButtonClick(LEFT)) + if (Xbox.getButtonClick(LEFT)) Serial.println(F("Left")); - if(Xbox.getButtonClick(RIGHT)) + if (Xbox.getButtonClick(RIGHT)) Serial.println(F("Right")); - if(Xbox.getButtonClick(START)) + if (Xbox.getButtonClick(START)) Serial.println(F("Start")); - if(Xbox.getButtonClick(BACK)) + if (Xbox.getButtonClick(BACK)) Serial.println(F("Back")); - if(Xbox.getButtonClick(L3)) + if (Xbox.getButtonClick(L3)) Serial.println(F("L3")); - if(Xbox.getButtonClick(R3)) + if (Xbox.getButtonClick(R3)) Serial.println(F("R3")); - if(Xbox.getButtonPress(A)) { + if (Xbox.getButtonPress(A)) { Serial.print(F("A: ")); Serial.println(Xbox.getButtonPress(A)); } - if(Xbox.getButtonPress(B)) { + if (Xbox.getButtonPress(B)) { Serial.print(F("B: ")); Serial.println(Xbox.getButtonPress(B)); } - if(Xbox.getButtonPress(X)) { + if (Xbox.getButtonPress(X)) { Serial.print(F("X: ")); Serial.println(Xbox.getButtonPress(X)); } - if(Xbox.getButtonPress(Y)) { + if (Xbox.getButtonPress(Y)) { Serial.print(F("Y: ")); Serial.println(Xbox.getButtonPress(Y)); } - if(Xbox.getButtonPress(L1)) { + if (Xbox.getButtonPress(L1)) { Serial.print(F("L1: ")); Serial.println(Xbox.getButtonPress(L1)); } - if(Xbox.getButtonPress(R1)) { + if (Xbox.getButtonPress(R1)) { Serial.print(F("R1: ")); Serial.println(Xbox.getButtonPress(R1)); } diff --git a/examples/Xbox/XBOXRECV/XBOXRECV.ino b/examples/Xbox/XBOXRECV/XBOXRECV.ino index 6bd33b0e..5896b9dc 100644 --- a/examples/Xbox/XBOXRECV/XBOXRECV.ino +++ b/examples/Xbox/XBOXRECV/XBOXRECV.ino @@ -1,7 +1,7 @@ /* Example sketch for the Xbox Wireless Reciver library - developed by Kristian Lauszus It supports up to four controllers wirelessly - For more information see the blog post: http://blog.tkjelectronics.dk/2012/12/xbox-360-receiver-added-to-the-usb-host-library/ or + For more information see the blog post: http://blog.tkjelectronics.dk/2012/12/xbox-360-receiver-added-to-the-usb-host-library/ or send me an e-mail: kristianl@tkjelectronics.com */ @@ -15,98 +15,100 @@ void setup() { while (!Serial); // Wait for serial port to connect - used on Leonardo, Teensy and other boards with built-in USB CDC serial connection if (Usb.Init() == -1) { Serial.print(F("\r\nOSC did not start")); - while(1); //halt + while (1); //halt } Serial.print(F("\r\nXbox Wireless Receiver Library Started")); } void loop() { Usb.Task(); - if(Xbox.XboxReceiverConnected) { - for(uint8_t i=0;i<4;i++) { - if(Xbox.Xbox360Connected[i]) { - if(Xbox.getButtonPress(L2,i) || Xbox.getButtonPress(R2,i)) { + if (Xbox.XboxReceiverConnected) { + for (uint8_t i = 0; i < 4; i++) { + if (Xbox.Xbox360Connected[i]) { + if (Xbox.getButtonPress(L2, i) || Xbox.getButtonPress(R2, i)) { Serial.print("L2: "); - Serial.print(Xbox.getButtonPress(L2,i)); + Serial.print(Xbox.getButtonPress(L2, i)); Serial.print("\tR2: "); - Serial.println(Xbox.getButtonPress(R2,i)); - Xbox.setRumbleOn(Xbox.getButtonPress(L2,i),Xbox.getButtonPress(R2,i),i); + Serial.println(Xbox.getButtonPress(R2, i)); + Xbox.setRumbleOn(Xbox.getButtonPress(L2, i), Xbox.getButtonPress(R2, i), i); } - if(Xbox.getAnalogHat(LeftHatX,i) > 7500 || Xbox.getAnalogHat(LeftHatX,i) < -7500 || Xbox.getAnalogHat(LeftHatY,i) > 7500 || Xbox.getAnalogHat(LeftHatY,i) < -7500 || Xbox.getAnalogHat(RightHatX,i) > 7500 || Xbox.getAnalogHat(RightHatX,i) < -7500 || Xbox.getAnalogHat(RightHatY,i) > 7500 || Xbox.getAnalogHat(RightHatY,i) < -7500) { - if(Xbox.getAnalogHat(LeftHatX,i) > 7500 || Xbox.getAnalogHat(LeftHatX,i) < -7500) { - Serial.print(F("LeftHatX: ")); - Serial.print(Xbox.getAnalogHat(LeftHatX,i)); + + if (Xbox.getAnalogHat(LeftHatX, i) > 7500 || Xbox.getAnalogHat(LeftHatX, i) < -7500 || Xbox.getAnalogHat(LeftHatY, i) > 7500 || Xbox.getAnalogHat(LeftHatY, i) < -7500 || Xbox.getAnalogHat(RightHatX, i) > 7500 || Xbox.getAnalogHat(RightHatX, i) < -7500 || Xbox.getAnalogHat(RightHatY, i) > 7500 || Xbox.getAnalogHat(RightHatY, i) < -7500) { + if (Xbox.getAnalogHat(LeftHatX, i) > 7500 || Xbox.getAnalogHat(LeftHatX, i) < -7500) { + Serial.print(F("LeftHatX: ")); + Serial.print(Xbox.getAnalogHat(LeftHatX, i)); Serial.print("\t"); - } - if(Xbox.getAnalogHat(LeftHatY,i) > 7500 || Xbox.getAnalogHat(LeftHatY,i) < -7500) { - Serial.print(F("LeftHatY: ")); - Serial.print(Xbox.getAnalogHat(LeftHatY,i)); + } + if (Xbox.getAnalogHat(LeftHatY, i) > 7500 || Xbox.getAnalogHat(LeftHatY, i) < -7500) { + Serial.print(F("LeftHatY: ")); + Serial.print(Xbox.getAnalogHat(LeftHatY, i)); Serial.print("\t"); - } - if(Xbox.getAnalogHat(RightHatX,i) > 7500 || Xbox.getAnalogHat(RightHatX,i) < -7500) { - Serial.print(F("RightHatX: ")); - Serial.print(Xbox.getAnalogHat(RightHatX,i)); - Serial.print("\t"); - } - if(Xbox.getAnalogHat(RightHatY,i) > 7500 || Xbox.getAnalogHat(RightHatY,i) < -7500) { - Serial.print(F("RightHatY: ")); - Serial.print(Xbox.getAnalogHat(RightHatY,i)); + } + if (Xbox.getAnalogHat(RightHatX, i) > 7500 || Xbox.getAnalogHat(RightHatX, i) < -7500) { + Serial.print(F("RightHatX: ")); + Serial.print(Xbox.getAnalogHat(RightHatX, i)); + Serial.print("\t"); + } + if (Xbox.getAnalogHat(RightHatY, i) > 7500 || Xbox.getAnalogHat(RightHatY, i) < -7500) { + Serial.print(F("RightHatY: ")); + Serial.print(Xbox.getAnalogHat(RightHatY, i)); } Serial.println(); } - if(Xbox.getButtonClick(UP,i)) { - Xbox.setLedOn(LED1,i); + if (Xbox.getButtonClick(UP, i)) { + Xbox.setLedOn(LED1, i); Serial.println(F("Up")); - } - if(Xbox.getButtonClick(DOWN,i)) { - Xbox.setLedOn(LED4,i); + } + if (Xbox.getButtonClick(DOWN, i)) { + Xbox.setLedOn(LED4, i); Serial.println(F("Down")); } - if(Xbox.getButtonClick(LEFT,i)) { - Xbox.setLedOn(LED3,i); + if (Xbox.getButtonClick(LEFT, i)) { + Xbox.setLedOn(LED3, i); Serial.println(F("Left")); } - if(Xbox.getButtonClick(RIGHT,i)) { - Xbox.setLedOn(LED2,i); + if (Xbox.getButtonClick(RIGHT, i)) { + Xbox.setLedOn(LED2, i); Serial.println(F("Right")); - } + } - if(Xbox.getButtonClick(START,i)) { - Xbox.setLedMode(ALTERNATING,i); + if (Xbox.getButtonClick(START, i)) { + Xbox.setLedMode(ALTERNATING, i); Serial.println(F("Start")); } - if(Xbox.getButtonClick(BACK,i)) { - Xbox.setLedBlink(ALL,i); + if (Xbox.getButtonClick(BACK, i)) { + Xbox.setLedBlink(ALL, i); Serial.println(F("Back")); } - if(Xbox.getButtonClick(L3,i)) + if (Xbox.getButtonClick(L3, i)) Serial.println(F("L3")); - if(Xbox.getButtonClick(R3,i)) + if (Xbox.getButtonClick(R3, i)) Serial.println(F("R3")); - if(Xbox.getButtonClick(L1,i)) + if (Xbox.getButtonClick(L1, i)) Serial.println(F("L1")); - if(Xbox.getButtonClick(R1,i)) + if (Xbox.getButtonClick(R1, i)) Serial.println(F("R1")); - if(Xbox.getButtonClick(XBOX,i)) { - Xbox.setLedMode(ROTATING,i); + if (Xbox.getButtonClick(XBOX, i)) { + Xbox.setLedMode(ROTATING, i); Serial.print(F("Xbox (Battery: ")); Serial.print(Xbox.getBatteryLevel(i)); // The battery level in the range 0-3 Serial.println(F(")")); } - if(Xbox.getButtonClick(SYNC,i)) + if (Xbox.getButtonClick(SYNC, i)) { Serial.println(F("Sync")); + Xbox.disconnect(i); + } - if(Xbox.getButtonClick(A,i)) + if (Xbox.getButtonClick(A, i)) Serial.println(F("A")); - if(Xbox.getButtonClick(B,i)) + if (Xbox.getButtonClick(B, i)) Serial.println(F("B")); - if(Xbox.getButtonClick(X,i)) + if (Xbox.getButtonClick(X, i)) Serial.println(F("X")); - if(Xbox.getButtonClick(Y,i)) + if (Xbox.getButtonClick(Y, i)) Serial.println(F("Y")); } } - } - delay(1); + } } diff --git a/examples/Xbox/XBOXUSB/XBOXUSB.ino b/examples/Xbox/XBOXUSB/XBOXUSB.ino index a26b4110..b7d5a625 100644 --- a/examples/Xbox/XBOXUSB/XBOXUSB.ino +++ b/examples/Xbox/XBOXUSB/XBOXUSB.ino @@ -1,6 +1,6 @@ /* Example sketch for the Xbox 360 USB library - developed by Kristian Lauszus - For more information visit my blog: http://blog.tkjelectronics.dk/ or + For more information visit my blog: http://blog.tkjelectronics.dk/ or send me an e-mail: kristianl@tkjelectronics.com */ @@ -14,90 +14,91 @@ void setup() { while (!Serial); // Wait for serial port to connect - used on Leonardo, Teensy and other boards with built-in USB CDC serial connection if (Usb.Init() == -1) { Serial.print(F("\r\nOSC did not start")); - while(1); //halt - } + while (1); //halt + } Serial.print(F("\r\nXBOX USB Library Started")); } void loop() { Usb.Task(); - if(Xbox.Xbox360Connected) { - if(Xbox.getButtonPress(L2) || Xbox.getButtonPress(R2)) { + if (Xbox.Xbox360Connected) { + if (Xbox.getButtonPress(L2) || Xbox.getButtonPress(R2)) { Serial.print("L2: "); Serial.print(Xbox.getButtonPress(L2)); Serial.print("\tR2: "); Serial.println(Xbox.getButtonPress(R2)); - Xbox.setRumbleOn(Xbox.getButtonPress(L2),Xbox.getButtonPress(R2)); + Xbox.setRumbleOn(Xbox.getButtonPress(L2), Xbox.getButtonPress(R2)); } else - Xbox.setRumbleOn(0,0); - if(Xbox.getAnalogHat(LeftHatX) > 7500 || Xbox.getAnalogHat(LeftHatX) < -7500 || Xbox.getAnalogHat(LeftHatY) > 7500 || Xbox.getAnalogHat(LeftHatY) < -7500 || Xbox.getAnalogHat(RightHatX) > 7500 || Xbox.getAnalogHat(RightHatX) < -7500 || Xbox.getAnalogHat(RightHatY) > 7500 || Xbox.getAnalogHat(RightHatY) < -7500) { - if(Xbox.getAnalogHat(LeftHatX) > 7500 || Xbox.getAnalogHat(LeftHatX) < -7500) { - Serial.print(F("LeftHatX: ")); + Xbox.setRumbleOn(0, 0); + + if (Xbox.getAnalogHat(LeftHatX) > 7500 || Xbox.getAnalogHat(LeftHatX) < -7500 || Xbox.getAnalogHat(LeftHatY) > 7500 || Xbox.getAnalogHat(LeftHatY) < -7500 || Xbox.getAnalogHat(RightHatX) > 7500 || Xbox.getAnalogHat(RightHatX) < -7500 || Xbox.getAnalogHat(RightHatY) > 7500 || Xbox.getAnalogHat(RightHatY) < -7500) { + if (Xbox.getAnalogHat(LeftHatX) > 7500 || Xbox.getAnalogHat(LeftHatX) < -7500) { + Serial.print(F("LeftHatX: ")); Serial.print(Xbox.getAnalogHat(LeftHatX)); Serial.print("\t"); - } - if(Xbox.getAnalogHat(LeftHatY) > 7500 || Xbox.getAnalogHat(LeftHatY) < -7500) { - Serial.print(F("LeftHatY: ")); + } + if (Xbox.getAnalogHat(LeftHatY) > 7500 || Xbox.getAnalogHat(LeftHatY) < -7500) { + Serial.print(F("LeftHatY: ")); Serial.print(Xbox.getAnalogHat(LeftHatY)); Serial.print("\t"); - } - if(Xbox.getAnalogHat(RightHatX) > 7500 || Xbox.getAnalogHat(RightHatX) < -7500) { - Serial.print(F("RightHatX: ")); + } + if (Xbox.getAnalogHat(RightHatX) > 7500 || Xbox.getAnalogHat(RightHatX) < -7500) { + Serial.print(F("RightHatX: ")); Serial.print(Xbox.getAnalogHat(RightHatX)); - Serial.print("\t"); - } - if(Xbox.getAnalogHat(RightHatY) > 7500 || Xbox.getAnalogHat(RightHatY) < -7500) { - Serial.print(F("RightHatY: ")); - Serial.print(Xbox.getAnalogHat(RightHatY)); + Serial.print("\t"); + } + if (Xbox.getAnalogHat(RightHatY) > 7500 || Xbox.getAnalogHat(RightHatY) < -7500) { + Serial.print(F("RightHatY: ")); + Serial.print(Xbox.getAnalogHat(RightHatY)); } Serial.println(); } - - if(Xbox.getButtonClick(UP)) { + + if (Xbox.getButtonClick(UP)) { Xbox.setLedOn(LED1); Serial.println(F("Up")); - } - if(Xbox.getButtonClick(DOWN)) { + } + if (Xbox.getButtonClick(DOWN)) { Xbox.setLedOn(LED4); Serial.println(F("Down")); } - if(Xbox.getButtonClick(LEFT)) { + if (Xbox.getButtonClick(LEFT)) { Xbox.setLedOn(LED3); Serial.println(F("Left")); } - if(Xbox.getButtonClick(RIGHT)) { + if (Xbox.getButtonClick(RIGHT)) { Xbox.setLedOn(LED2); Serial.println(F("Right")); } - if(Xbox.getButtonClick(START)) { + if (Xbox.getButtonClick(START)) { Xbox.setLedMode(ALTERNATING); Serial.println(F("Start")); } - if(Xbox.getButtonClick(BACK)) { + if (Xbox.getButtonClick(BACK)) { Xbox.setLedBlink(ALL); Serial.println(F("Back")); } - if(Xbox.getButtonClick(L3)) + if (Xbox.getButtonClick(L3)) Serial.println(F("L3")); - if(Xbox.getButtonClick(R3)) + if (Xbox.getButtonClick(R3)) Serial.println(F("R3")); - if(Xbox.getButtonClick(L1)) + if (Xbox.getButtonClick(L1)) Serial.println(F("L1")); - if(Xbox.getButtonClick(R1)) + if (Xbox.getButtonClick(R1)) Serial.println(F("R1")); - if(Xbox.getButtonClick(XBOX)) { + if (Xbox.getButtonClick(XBOX)) { Xbox.setLedMode(ROTATING); - Serial.println(F("Xbox")); + Serial.println(F("Xbox")); } - if(Xbox.getButtonClick(A)) + if (Xbox.getButtonClick(A)) Serial.println(F("A")); - if(Xbox.getButtonClick(B)) + if (Xbox.getButtonClick(B)) Serial.println(F("B")); - if(Xbox.getButtonClick(X)) + if (Xbox.getButtonClick(X)) Serial.println(F("X")); - if(Xbox.getButtonClick(Y)) + if (Xbox.getButtonClick(Y)) Serial.println(F("Y")); } delay(1); diff --git a/examples/adk/ArduinoBlinkLED/ArduinoBlinkLED.ino b/examples/adk/ArduinoBlinkLED/ArduinoBlinkLED.ino index 23b25ecc..bc0cb95a 100644 --- a/examples/adk/ArduinoBlinkLED/ArduinoBlinkLED.ino +++ b/examples/adk/ArduinoBlinkLED/ArduinoBlinkLED.ino @@ -3,42 +3,55 @@ #include USB Usb; -ADK adk(&Usb,"TKJElectronics", // Manufacturer Name - "ArduinoBlinkLED", // Model Name - "Example sketch for the USB Host Shield", // Description (user-visible string) - "1.0", // Version - "http://www.tkjelectronics.dk/uploads/ArduinoBlinkLED.apk", // URL (web page to visit if no installed apps support the accessory) - "123456789"); // Serial Number (optional) +ADK adk(&Usb, "TKJElectronics", // Manufacturer Name + "ArduinoBlinkLED", // Model Name + "Example sketch for the USB Host Shield", // Description (user-visible string) + "1.0", // Version + "http://www.tkjelectronics.dk/uploads/ArduinoBlinkLED.apk", // URL (web page to visit if no installed apps support the accessory) + "123456789"); // Serial Number (optional) -#define LED 13 // Pin 13 is occupied by the SCK pin on a normal Arduino (Uno, Duemilanove etc.), so use a different pin +#define LED LED_BUILTIN // Use built in LED - note that pin 13 is occupied by the SCK pin on a normal Arduino (Uno, Duemilanove etc.), so use a different pin -void setup() -{ +uint32_t timer; + +void setup() { Serial.begin(115200); while (!Serial); // Wait for serial port to connect - used on Leonardo, Teensy and other boards with built-in USB CDC serial connection if (Usb.Init() == -1) { Serial.print("\r\nOSCOKIRQ failed to assert"); - while(1); //halt + while (1); // halt } pinMode(LED, OUTPUT); Serial.print("\r\nArduino Blink LED Started"); } -void loop() -{ +void loop() { Usb.Task(); - if(adk.isReady()) { + if (adk.isReady()) { uint8_t msg[1]; uint16_t len = sizeof(msg); uint8_t rcode = adk.RcvData(&len, msg); - if(rcode && rcode != hrNAK) - USBTRACE2("Data rcv. :", rcode); - if(len > 0) { + if (rcode && rcode != hrNAK) { + Serial.print(F("\r\nData rcv: ")); + Serial.print(rcode, HEX); + } else if (len > 0) { Serial.print(F("\r\nData Packet: ")); Serial.print(msg[0]); - digitalWrite(LED,msg[0] ? HIGH : LOW); + digitalWrite(LED, msg[0] ? HIGH : LOW); } - } + + if (millis() - timer >= 1000) { // Send data every 1s + timer = millis(); + rcode = adk.SndData(sizeof(timer), (uint8_t*)&timer); + if (rcode && rcode != hrNAK) { + Serial.print(F("\r\nData send: ")); + Serial.print(rcode, HEX); + } else if (rcode != hrNAK) { + Serial.print(F("\r\nTimer: ")); + Serial.print(timer); + } + } + } else - digitalWrite(LED, LOW); + digitalWrite(LED, LOW); } diff --git a/examples/testusbhostFAT/Arduino_Makefile_master b/examples/testusbhostFAT/Arduino_Makefile_master index 7f1fe2f8..139b9c8b 160000 --- a/examples/testusbhostFAT/Arduino_Makefile_master +++ b/examples/testusbhostFAT/Arduino_Makefile_master @@ -1 +1 @@ -Subproject commit 7f1fe2f8ec3db4d1bd0a5c516dd379e2539d1303 +Subproject commit 139b9c8be59a62e8fb1e8f983ac9bac2b9b9d582 diff --git a/examples/testusbhostFAT/Makefile b/examples/testusbhostFAT/Makefile index 191238a0..7e5ebaec 100644 --- a/examples/testusbhostFAT/Makefile +++ b/examples/testusbhostFAT/Makefile @@ -43,12 +43,12 @@ EXTRA_FLAGS += -D USB_HOST_SERIAL=Serial3 #EXTRA_FLAGS += -D DEBUG_USB_HOST # The following are the libraries used. -LIB_DIRS = -LIB_DIRS += ../libraries/xmem -LIB_DIRS += ../libraries/USB_Host_Shield_2_0 -LIB_DIRS += ../libraries/generic_storage -LIB_DIRS += ../libraries/RTClib +LIB_DIRS += ../../ +LIB_DIRS += ../testusbhostFAT/xmem2 +LIB_DIRS += ../testusbhostFAT/generic_storage +LIB_DIRS += ../testusbhostFAT/RTClib LIB_DIRS += $(ARD_HOME)/libraries/Wire LIB_DIRS += $(ARD_HOME)/libraries/Wire/utility + # And finally, the part that brings everything together for you. -include ../Arduino_Makefile_master/_Makefile.master +include Arduino_Makefile_master/_Makefile.master diff --git a/examples/testusbhostFAT/RTClib b/examples/testusbhostFAT/RTClib index cb8b5690..a4bd6f50 160000 --- a/examples/testusbhostFAT/RTClib +++ b/examples/testusbhostFAT/RTClib @@ -1 +1 @@ -Subproject commit cb8b5690c7d683e0c24e6894ff05552f83240714 +Subproject commit a4bd6f500f70599847de60973371ee973d094a34 diff --git a/examples/testusbhostFAT/generic_storage b/examples/testusbhostFAT/generic_storage index db5de2fe..1d481775 160000 --- a/examples/testusbhostFAT/generic_storage +++ b/examples/testusbhostFAT/generic_storage @@ -1 +1 @@ -Subproject commit db5de2fe3c2e0d2d96de98864b1b6e00e172f727 +Subproject commit 1d481775b5096a172edf607062278a86e9618a15 diff --git a/examples/testusbhostFAT/testusbhostFAT.ino b/examples/testusbhostFAT/testusbhostFAT.ino index c462fa92..49713d36 100644 --- a/examples/testusbhostFAT/testusbhostFAT.ino +++ b/examples/testusbhostFAT/testusbhostFAT.ino @@ -47,8 +47,11 @@ ///////////////////////////////////////////////////////////// // End of Arduino IDE specific hacks // ///////////////////////////////////////////////////////////// - +#if defined(AVR) #include +#else +#include +#endif #if WANT_HUB_TEST #include #endif @@ -59,22 +62,23 @@ #include #include #include - +#include +#if defined(AVR) static FILE tty_stdio; static FILE tty_stderr; -USB Usb; - -#define LED 13 // the pin that the LED is attached to - +volatile uint32_t LEDnext_time; // fade timeout +volatile uint32_t HEAPnext_time; // when to print out next heap report volatile int brightness = 0; // how bright the LED is volatile int fadeAmount = 80; // how many points to fade the LED by +#endif + +USB Usb; + volatile uint8_t current_state = 1; -volatile uint32_t LEDnext_time; // fade timeout volatile uint8_t last_state = 0; volatile boolean fatready = false; volatile boolean partsready = false; volatile boolean notified = false; -volatile uint32_t HEAPnext_time; // when to print out next heap report volatile boolean runtest = false; volatile boolean usbon = false; volatile uint32_t usbon_time; @@ -96,6 +100,7 @@ static storage_t sto[_VOLUMES]; #define mbxs 128 static uint8_t My_Buff_x[mbxs]; /* File read buffer */ +#if defined(AVR) #define prescale1 ((1 << WGM12) | (1 << CS10)) #define prescale8 ((1 << WGM12) | (1 << CS11)) @@ -110,6 +115,11 @@ static int tty_stderr_putc(char c, FILE *t) { return 0; } +static int tty_stderr_flush(FILE *t) { + USB_HOST_SERIAL.flush(); + return 0; +} + static int tty_std_putc(char c, FILE *t) { Serial.write(c); return 0; @@ -120,6 +130,49 @@ static int tty_std_getc(FILE *t) { return Serial.read(); } +static int tty_std_flush(FILE *t) { + Serial.flush(); + return 0; +} + +#else +extern "C" { + + int _write(int fd, const char *ptr, int len) { + int j; + for (j = 0; j < len; j++) { + if (fd == 1) + Serial.write(*ptr++); + else if (fd == 2) + USB_HOST_SERIAL.write(*ptr++); + } + return len; + } + + int _read(int fd, char *ptr, int len) { + if (len > 0 && fd == 0) { + while (!Serial.available()); + *ptr = Serial.read(); + return 1; + } + return 0; + } + +#include + + int _fstat(int fd, struct stat *st) { + memset(st, 0, sizeof (*st)); + st->st_mode = S_IFCHR; + st->st_blksize = 1024; + return 0; + } + + int _isatty(int fd) { + return (fd < 3) ? 1 : 0; + } +} +#endif + void setup() { boolean serr = false; for (int i = 0; i < _VOLUMES; i++) { @@ -130,8 +183,10 @@ void setup() { // Set this to higher values to enable more debug information // minimum 0x00, maximum 0xff UsbDEBUGlvl = 0x51; + +#if defined(AVR) // make LED pin as an output: - pinMode(LED, OUTPUT); + pinMode(LED_BUILTIN, OUTPUT); pinMode(2, OUTPUT); // Ensure TX is off _SFR_BYTE(UCSR0B) &= ~_BV(TXEN0); @@ -148,21 +203,26 @@ void setup() { tty_stdio.get = tty_std_getc; tty_stdio.flags = _FDEV_SETUP_RW; tty_stdio.udata = 0; - stdout = &tty_stdio; - stdin = &tty_stdio; tty_stderr.put = tty_stderr_putc; tty_stderr.get = NULL; tty_stderr.flags = _FDEV_SETUP_WRITE; tty_stderr.udata = 0; + + stdout = &tty_stdio; + stdin = &tty_stdio; stderr = &tty_stderr; // Blink LED delay(500); - analogWrite(LED, 255); + analogWrite(LED_BUILTIN, 255); delay(500); - analogWrite(LED, 0); + analogWrite(LED_BUILTIN, 0); delay(500); +#else + while (!Serial); +#endif + printf_P(PSTR("\r\n\n\n\n\n\n\n\n\n\n\n\n\n\n\nStart\r\n")); printf_P(PSTR("Current UsbDEBUGlvl %02x\r\n"), UsbDEBUGlvl); printf_P(PSTR("'+' and '-' increase/decrease by 0x01\r\n")); @@ -187,17 +247,19 @@ void setup() { #endif "\r\n")); } - analogWrite(LED, 255); +#if defined(AVR) + + analogWrite(LED_BUILTIN, 255); delay(500); - analogWrite(LED, 0); + analogWrite(LED_BUILTIN, 0); delay(500); - analogWrite(LED, 255); + analogWrite(LED_BUILTIN, 255); delay(500); - analogWrite(LED, 0); + analogWrite(LED_BUILTIN, 0); delay(500); - analogWrite(LED, 255); + analogWrite(LED_BUILTIN, 255); delay(500); - analogWrite(LED, 0); + analogWrite(LED_BUILTIN, 0); delay(500); LEDnext_time = millis() + 1; @@ -206,6 +268,7 @@ void setup() { #endif printf_P(PSTR("Available heap: %u Bytes\r\n"), freeHeap()); printf_P(PSTR("SP %x\r\n"), (uint8_t *)(SP)); +#endif // Even though I'm not going to actually be deleting, // I want to be able to have slightly more control. @@ -213,7 +276,9 @@ void setup() { #if WANT_HUB_TEST for (int i = 0; i < MAX_HUBS; i++) { Hubs[i] = new USBHub(&Usb); +#if defined(AVR) printf_P(PSTR("Available heap: %u Bytes\r\n"), freeHeap()); +#endif } #endif // Initialize generic storage. This must be done before USB starts. @@ -223,10 +288,8 @@ void setup() { printf_P(PSTR("No USB HOST Shield?\r\n")); Notify(PSTR("OSC did not start."), 0x40); } - // usb VBUS _OFF_ - //Usb.gpioWr(0x00); - //digitalWrite(2, 0); - //usbon_time = millis() + 2000; + +#if defined(AVR) cli(); TCCR3A = 0; TCCR3B = 0; @@ -237,6 +300,32 @@ void setup() { sei(); HEAPnext_time = millis() + 10000; +#else +#if 0 + // + // On the teensy 3 we can raise the speed of SPI here. + // + // Default seen is 0xB8011001. + // + + uint32_t ctar = SPI0_CTAR0; + //printf("SPI_CTAR0 = %8.8X\r\n", ctar); + ctar &= 0x7FFCFFF0; // 1/4 fSYS, 12.5Mhz + //printf("SPI_CTAR0 = %8.8X\r\n", ctar); + ctar |= 0x80000000; // 1/2 fSYS 25Mhz + //printf("SPI_CTAR0 = %8.8X\r\n", ctar); + + uint32_t mcr = SPI0_MCR; + if (mcr & SPI_MCR_MDIS) { + SPI0_CTAR0 = ctar; + } else { + SPI0_MCR = mcr | SPI_MCR_MDIS | SPI_MCR_HALT; + SPI0_CTAR0 = ctar; + SPI0_MCR = mcr; + } +#endif +#endif + } void serialEvent() { @@ -278,12 +367,14 @@ void serialEvent() { } } +#if defined(AVR) + ISR(TIMER3_COMPA_vect) { if (millis() >= LEDnext_time) { LEDnext_time = millis() + 30; // set the brightness of LED - analogWrite(LED, brightness); + analogWrite(LED_BUILTIN, brightness); // change the brightness for next time through the loop: brightness = brightness + fadeAmount; @@ -299,6 +390,7 @@ ISR(TIMER3_COMPA_vect) { } } } +#endif bool isfat(uint8_t t) { return (t == 0x01 || t == 0x04 || t == 0x06 || t == 0x0b || t == 0x0c || t == 0x0e || t == 0x1); @@ -312,6 +404,7 @@ void die(FRESULT rc) { void loop() { FIL My_File_Object_x; /* File object */ +#if defined(AVR) // Print a heap status report about every 10 seconds. if (millis() >= HEAPnext_time) { if (UsbDEBUGlvl > 0x50) { @@ -319,7 +412,11 @@ void loop() { } HEAPnext_time = millis() + 10000; } - + TCCR3B = 0; +#else + // Arm suffers here, oh well... + serialEvent(); +#endif // Horrid! This sort of thing really belongs in an ISR, not here! // We also will be needing to test each hub port, we don't do this yet! if (!change && !usbon && millis() >= usbon_time) { @@ -342,11 +439,15 @@ void loop() { if (current_state != last_state) { if (UsbDEBUGlvl > 0x50) printf_P(PSTR("USB state = %x\r\n"), current_state); +#if defined(AVR) if (current_state == USB_STATE_RUNNING) { fadeAmount = 30; } +#endif if (current_state == USB_DETACHED_SUBSTATE_WAIT_FOR_DEVICE) { +#if defined(AVR) fadeAmount = 80; +#endif partsready = false; for (int i = 0; i < cpart; i++) { if (Fats[i] != NULL) @@ -365,10 +466,10 @@ void loop() { if (partsready && !fatready) { if (cpart > 0) fatready = true; } - // This is horrible, and needs to be moved elsewhere! for (int B = 0; B < MAX_USB_MS_DRIVERS; B++) { - if (!partsready && Bulk[B]->GetAddress() != NULL) { + if (!partsready && (Bulk[B]->GetAddress() != NULL)) { + // Build a list. int ML = Bulk[B]->GetbMaxLUN(); //printf("MAXLUN = %i\r\n", ML); @@ -376,8 +477,8 @@ void loop() { for (int i = 0; i < ML; i++) { if (Bulk[B]->LUNIsGood(i)) { partsready = true; - ((pvt_t *)sto[i].private_data)->lun = i; - ((pvt_t *)sto[i].private_data)->B = B; + ((pvt_t *)(sto[i].private_data))->lun = i; + ((pvt_t *)(sto[i].private_data))->B = B; sto[i].Read = *PRead; sto[i].Write = *PWrite; sto[i].Reads = *PReads; @@ -440,7 +541,9 @@ void loop() { p = ((struct Pvt *)(Fats[0]->storage->private_data)); if (!Bulk[p->B]->LUNIsGood(p->lun)) { // media change +#if defined(AVR) fadeAmount = 80; +#endif partsready = false; for (int i = 0; i < cpart; i++) { if (Fats[i] != NULL) @@ -459,11 +562,13 @@ void loop() { UINT bw, br, i; if (!notified) { +#if defined(AVR) fadeAmount = 5; +#endif notified = true; printf_P(PSTR("\r\nOpen an existing file (message.txt).\r\n")); rc = f_open(&My_File_Object_x, "0:/MESSAGE.TXT", FA_READ); - if (rc) printf_P(PSTR("Error %i, message.txt not found.\r\n")); + if (rc) printf_P(PSTR("Error %i, message.txt not found.\r\n"), rc); else { printf_P(PSTR("\r\nType the file content.\r\n")); for (;;) { @@ -522,7 +627,9 @@ outdir: } printf_P(PSTR("\r\nDirectory listing...\r\n")); +#if defined(AVR) printf_P(PSTR("Available heap: %u Bytes\r\n"), freeHeap()); +#endif for (;;) { #if _USE_LFN My_File_Info_Object_x.lfsize = _MAX_LFN; @@ -583,7 +690,9 @@ out: rc = f_open(&My_File_Object_x, "0:/10MB.bin", FA_WRITE | FA_CREATE_ALWAYS); if (rc) goto failed; for (bw = 0; bw < mbxs; bw++) My_Buff_x[bw] = bw & 0xff; + fflush(stdout); start = millis(); + while (start == millis()); for (ii = 10485760LU / mbxs; ii > 0LU; ii--) { rc = f_write(&My_File_Object_x, My_Buff_x, mbxs, &bw); if (rc || !bw) goto failed; @@ -591,10 +700,12 @@ out: rc = f_close(&My_File_Object_x); if (rc) goto failed; end = millis(); - wt = end - start; + wt = (end - start) - 1; printf_P(PSTR("Time to write 10485760 bytes: %lu ms (%lu sec) \r\n"), wt, (500 + wt) / 1000UL); rc = f_open(&My_File_Object_x, "0:/10MB.bin", FA_READ); + fflush(stdout); start = millis(); + while (start == millis()); if (rc) goto failed; for (;;) { rc = f_read(&My_File_Object_x, My_Buff_x, mbxs, &bw); /* Read a chunk of file */ @@ -604,7 +715,7 @@ out: if (rc) goto failed; rc = f_close(&My_File_Object_x); if (rc) goto failed; - rt = end - start; + rt = (end - start) - 1; printf_P(PSTR("Time to read 10485760 bytes: %lu ms (%lu sec)\r\nDelete test file\r\n"), rt, (500 + rt) / 1000UL); failed: if (rc) die(rc); @@ -613,3 +724,4 @@ failed: } } } + diff --git a/examples/testusbhostFAT/xmem2 b/examples/testusbhostFAT/xmem2 index 16374f68..9fe733d3 160000 --- a/examples/testusbhostFAT/xmem2 +++ b/examples/testusbhostFAT/xmem2 @@ -1 +1 @@ -Subproject commit 16374f681b31d411661b7bd9ff5e578b2dff6843 +Subproject commit 9fe733d35304dec1ebe750f5f13f868def2fcfe4 diff --git a/keywords.txt b/keywords.txt index b68eda9c..6847bb09 100644 --- a/keywords.txt +++ b/keywords.txt @@ -34,7 +34,10 @@ PS3USB KEYWORD1 # Methods and Functions (KEYWORD2) #################################################### setBdaddr KEYWORD2 +getBdaddr KEYWORD2 setMoveBdaddr KEYWORD2 +getMoveBdaddr KEYWORD2 +getMoveCalibration KEYWORD2 getButtonPress KEYWORD2 getButtonClick KEYWORD2